Login | Register

HIGH FLUX DENSITY ROTATIONAL CORE LOSS MEASUREMENTS

Title:

HIGH FLUX DENSITY ROTATIONAL CORE LOSS MEASUREMENTS

Wanjiku, John Gitonga (2015) HIGH FLUX DENSITY ROTATIONAL CORE LOSS MEASUREMENTS. PhD thesis, Concordia University.

[img]
Preview
Text (application/pdf)
Wanjiku_PhD_S2016.pdf - Accepted Version
6MB

Abstract

Energy conversion processes involve losses. Specifically core losses, which are a result of the magnetization process in cored electrical energy conversion and storage devices. The cores are made of soft ferromagnetic materials that are easily magnetized and demagnetized. These soft magnetic cores, allow a reduction in size, higher energy storage density, and a reduction in magnetizing current, when compared to non-cored devices.
The characterization of soft ferromagnetic materials is traditionally done under unidirectional pulsating fields, which is sufficient for single-phase transformers and inductors, where the cores are under pulsating fields. However, T-joints of three phase transformers and teeth-roots of rotating machine stator cores are exposed to two-dimensional rotational fields of higher core loss. Pulsating measurements are therefore insufficient in the characterization of soft ferromagnetic materials used in rotating electrical machines or in three phase transformers. In two-dimensional fields, the magnetization direction changes with time, tracing a flux density locus. This requires the measurement of tangential magnetic field and flux density components, hence the associated loss.
This study proposes a two-dimensional rotational core loss tester for high flux density measurements up to about 2 T, at 60 Hz. Its frequency measurement range is from 60 Hz to 1 kHz. The initial sizing was done analytically, then implemented in three-dimensional finite element analysis, prototyped and experiments performed to verify its capability.
It was validated by testing two 0.35 mm and 0.65 mm thick samples. Very high flux densities in the range of 2 T at 60 Hz were achieved in both samples. For the thinner sample, flux densities of 1.8 T and 1.6 T were measured at 400 Hz and 1 kHz, respectively, while for the thicker one, the range reduced to 1.7 T and 1.4 T, at 400 Hz and 1 kHz, respectively. The magnetizer also reproduced non-sinusoidal flux density waveforms, for flux densities less than or equal to 1.0 T, without any waveform control.
The proposed rotational core loss setup will find application in the characterization of electrical steels, and generation of pulsating and rotational core loss data. This data can then be applied in core loss models, uprating of megawatt (MW) rated machines, transient and hotspots analysis, and in the design of higher power density machines, such as high-speed machines.

Divisions:Concordia University > Gina Cody School of Engineering and Computer Science > Electrical and Computer Engineering
Item Type:Thesis (PhD)
Authors:Wanjiku, John Gitonga
Institution:Concordia University
Degree Name:Ph. D.
Program:Electrical and Computer Engineering
Date:25 November 2015
Thesis Supervisor(s):Pillay, Pragasen
Keywords:Core losses, Core loss measurements, Rotational core losses, Measurement errors, Machine design, Single sheet testers, Magnetic materials, Magnetic measurements, Shields, Round rotational single sheet testers, Standards, Systematic error, Random errors, Error estimation, Leakage field, Magnetic field measurements, Flux density measurements, Uncertainty
ID Code:980896
Deposited By: JOHN GITONGA WANJIKU
Deposited On:16 Jun 2016 15:49
Last Modified:18 Jan 2018 17:52

References:

[1] G. McCoy, T. Litman and J. Douglass, "Energy-Efficient Motor Selection Handbook," Pullman, 1993.
[2] M. M. Znidarich, "Hydro Generator Stator Cores Part 1 - Construction Features and Core Losses," in 2008 Australasian Universities Power Engineering Conference (AUPEC '08).
[3] G. Seggewiss, J. Dai and M. Fanslow, "Synchronous Motors on Grinding Mills: The Different Excitation Types and Resulting Performance Characteristics with VFD Control for New or Retrofit Installations," IEEE Industry Applications Magazine, vol. 21, pp. 60-67, Nov-Dec 2015.
[4] J. Gieras, "New Applications of Synchronous Generators," Przeglad Elektrotechniczny (Electrical Review), no. 09a/2012, pp. 150-157.
[5] M. A. Plonus, Applied Electromagnetics, McGraw-Hill, Inc., 1978.
[6] Y. Zhang, "Expermental, Theoretical and Numerical Invesitgation of Core Losses in Laminated Magnetic Materials," PhD Thesis, Clarkson University, Potsdam, 2008.
[7] G. Bertotti, Hysteresis in Magnetism, Academic Press, 1998.
[8] J. Akiror, A. Merkhouf, C. Hudon and P. Pillay, "Consideration of Design and Operation on Rotational Flux Density Distribution in Hydrogenerator Stators," IEEE Trans. Energy Conver., 2015.
[9] J. W. Macki, P. Nistri and P. Zecca, "Mathematical Models for Hysteresis," Soc. Indu. Appl. Mathe., vol. 35, no. 1, pp. 94-123, 1993.
[10] H. Hauser, "Energetic Model of Ferromagnetic Hysteresis: Isotropic Magnetization," J. Appl. Phys., vol. 96, no. 5, pp. 2753-2767, 2004.
[11] L. Dupré and J. Melkebeek, "Electromagnetic hysteresis modelling: from material science to finite element analysis of devices," International Compumag Society Newsletter, pp. 4-15, 2003.
[12] R. Szewczyk, "Application of Jiles-Atherton Model for Modelling Magnetization Characteristics of Textured Electrical Steel Magnetized in Easy or Hard Axis," Progress in Automation Robotics and Measuring Techniques, pp. 293-302, 2015.
[13] K.-J. Ko, S.-K. Jang, J.-Y. Choi, S.-H. Lee and Y.-B. Lee, "A core loss calculation based on magnetic field analysis considering the time harmonics of high-speed permanent magnet machine according to driving method," in IEEE International Conference on Electrical Machines and Systems (ICEMS), 2010.
[14] L. Ma, M. Sanada, S. Morimoto and Y. Takeda, "Prediction of iron loss in rotating machines with rotational loss included," IEEE Transactions on Magnetics, vol. 39, no. 4, pp. 2036-2041, July 2003.
[15] H. Domeki, Y. Ishihara, C. Kaido, Y. Kawase, S. Kitamura, T. Shimomura, N. Takahashi, T. Yamada and K. Yamazaki, "Investigation of benchmark model for estimating iron loss in rotating machine," IEEE Transactions on Magnetics, vol. 40, no. 2, pp. 794-797, March 2004.
[16] J. Zhu and V. Ramsden, "Improved formulations for rotational core losses in rotating electrical machines," IEEE Transactions on Magnetics, vol. 34, no. 4, pp. 2234-2242, July 1998.
[17] C. Appino, O. de la Barriere, C. Beatrice, F. Fiorillo and C. Ragusa, "Rotational Magnetic Losses in Nonoriented Fe–Si and Fe–Co Laminations up to the kilohertz Range," IEEE Trans. Magn., vol. 50, no. 11, pp. 1-4, 2014.
[18] VACUUMSCHMELZE GMBH & CO. KG , "Soft Magentic Cobalt-Iron-Alloys," 2001.
[19] Aperam Alloys Imphy, "Nickel Iron and Cobalt Iron Cold Rolled Strips," 2013.
[20] H. Pfutzner et al, "Rotational Magnetization in Transformer Cores - A Review," IEEE Trans. Magn., vol. 47, no. 11, pp. 4523-4533, November 2011.
[21] C. Kittel, "Physical Theory of Ferromagnetic Domains," Reviews of Modern Physics, vol. 21, no. 4, pp. 541-583, October 1949.
[22] A. Hubert and R. Schafer, Magnetic Domains: The Analysis of Magnetic Microstructures, 3rd Printing ed., Springer, 2008.
[23] F. Baily, "The Hysteresis of Iron and Steel in a Rotating Magnetic Field," Phil. Trans. of the R. Soc. Lond., vol. 187, pp. 715-746, January 1896.
[24] B. Zawilski, D. Maillard, O. Geoffroy and D. Dufeu, "Rotating Sample Magnetometer for Precise, Real Time Differential Measurements," Rev. Sci. Intrum., vol. 77, 2006.
[25] R. Gimaev, Y. Spichkin, M. Plyashkevich and A. Tishin, "Rotating-Sample Magnetometer for Measuring Crystal Field Parameters," Solid State Phenomena, vol. 190, pp. 175-178, June 2012.
[26] J. Rigue, D. Chrischon, A. H de Andrade and M. Carara, "A Torque Magnetometer for Thin Films Applications," J. Magn. Magn. Mater, vol. 324, no. 8, pp. 1561-1564, April 2012.
[27] J. Sievert, H. Ahlers, M. Enokizono, S. Kauke, L. Rahf and J. Xu, "The Measurement of Rotational Power Loss in Electrical Sheet Steel Using a Vertical Yoke System," J. Magn. Magn. Mater., vol. 112, pp. 91-94, 1992.
[28] C. Ragusa, S. Zurek, C. Appino and A. Moses, "An Intercomparison of Rotational Loss Measurements in Non-Oriented Fe-Si Alloys," J. Magn. Magn. Mater., vol. 320, no. 20, pp. e623-e626, October 2004.
[29] H. Hamzehbahmani, A. Moses and F. Anayi, "Opportunities and Precautions in Measurements of Power Loss in Electrical Steel Laminations Using Initial Rate of Rise of Temperature Method," IEEE Trans. Magn., vol. 49, no. 3, March 2013.
[30] K. Atallah and D. Howe, "Calculation of the Rotational Power Loss in Electrical Steel Laminations from the Measured H and B," IEEE Trans. on Magn., vol. 29, no. 6, pp. 3547-3549, November 1993.
[31] S. Zurek and T. Meydan, "Errors in the power loss measured in CW and ACW rotational magnetisation. Part 1: Mathematical study," IEE Proc.-Sci. Meas. Technol., vol. 153, no. 4, pp. 147-151, July 2006.
[32] C. Appino, F. Fiorillo and C. Ragusa, "One-Dimension/Two-Dimension Loss Measurements up to High Inductions," J. Appl. Phys., vol. 105, no. 07E718, 2009.
[33] M. Enokizono and H. Matsuo, "A Measurement System for Two-Dimensional DC Biased Properties of Magnetic Materials," J. Magn. Magn. Mater., Vols. 254-255, pp. 39-42, January 2003.
[34] A. Basak and A. Moses, "Influence of Stress on Rotational Loss in Silicon Iron," Proc. IEE, vol. 125, no. 2, pp. 165-168, February 1978.
[35] T. Sasaki, M. Imamura, S. Takada and Y. Suzuki, "Measurement of Rotational Power Losses in Silicon-Iron Sheets Using Wattmeter Method," IEEE Trans. Magn., vol. 21, no. 5, pp. 1918-1920, September 1985.
[36] S. Yanase, M. Uchiyama, S. Ishikawa and Y. Okazaki, "AC Magnetic Properties of Electrical Steel Sheet Under DC-Biased Magnetization," Przeglad Elektrotechniczny (Electrical Review), vol. R. 87, no. 9b, pp. 52-56, 2011.
[37] M. Jesenik, V. Gorican, M. Trlep, A. Hamler and B. Stumberger, "Eddy Current Effects in the Sample of 2D RRSST and in the Sample of 2D SRSST," in 11th Intern. Symp. on Electromag. Fields in Elect. Eng. (ISEF 2003), Slovenia, 2003.
[38] Y. Li, Y. Qingxin, J. G. Zhu, Z. Zhigang, L. Xiaojing and Z. Changgeng, "Design and Analysis of a Novel 3-D Magnetization Structure for Laminated Silicon Steel," IEEE Trans. Magn., vol. 50, no. 2, pp. 389-392, 2014.
[39] K. Mori, S. Yanase, Y. Okazaki and S. Hashi, "2-D Magnetic Rotational Loss of Electrical Steel at High Magnetic Flux Density," IEEE Tran. Magn., vol. 41, no. 10, pp. 3310-3312, October 2005.
[40] Y. Maeda, S. Urata, Y. Kano, T. Arakawa, S. Yanase, Y. Okazaki and S. Watanabe, "Examination of Measurement Apparatus for 2D Magnetic Properties," Elect. Comm. Japan, vol. 96, no. 2, pp. 57-64, 2013.
[41] J. Zhu, J. Zhong, Z. Lin and J. Sievert, "Measurement of Magnetic Properties Under 3-D Magnetic Excitations," IEEE Trans. Magn., vol. 39, no. 5, pp. 3429-3431, September 2003.
[42] H. Shokrollahi and K. Janghorban, "Soft magnetic composite materials (SMCs)," Mater. Proc. Tech., vol. 189, no. 1, pp. 1-12, 2007.
[43] V. Gorican, A. Hamler, B. Hribernik, M. Jesenik and M. Trlep, "2-D Measurements of Magnetic Properties Using a Round RSST," in 1&2-D Magn. Meas. & Test., Bad Gastein, 2000.
[44] A. Hasenzagl, B. Weiser and H. Pfutzner, "Novel 3-Phase Excited Single Sheet Tester for Rotational Magnetization," J. Magn. Magn. Mater., vol. 160, pp. 180-182, 1996.
[45] N. Alatawneh and P. Pillay, "Design of a Novel Test Fixture to Measure Rotational Core losses in Machine Laminations," IEEE Trans. Indu. Applicat., vol. 48, no. 5, pp. 1467-1477, 2012.
[46] O. de la Barriere, C. Appino, F. Fiorillo, C. Ragusa, M. Lecrivain, L. Rocchino, H. B. Ahmed, M. Gabsi, F. Mazaleyrat and M. LoBue, "Extended frequency analysis of magnetic losses under rotating induction in soft magnetic composites," J. Appl. Physics, vol. 111, no. 07e325, 2012.
[47] J. Zhu, "Numerical Modelling of Magnetic Materials for Computer Aided Design of Electromagnetic Devices," PhD Thesis, University of Technology , Sydney, 1994.
[48] A. Jander, C. Smith and R. Schneider, "Magnetoresistive Sensors for Nondestructive Evaluation," in International Symp. Conf. on Nondestructive Evaluation for Health Monitoring and Diaganostics, 2005.
[49] B. Fryskowski, "Experimental Evaluation of Magnetic Anisotropy in Electrical Steel Sheets," J. Magn. Magn. Mater., vol. 320, pp. 515-522, 2008.
[50] H. Mason, "Basic Introduction to the Use of Magentoresisitve Sensors," Application Note 37, ZETEX Semiconductor, 2003.
[51] A.-. E. Abdallh and L. Dupre, "A Rogowski-Chattock Coil for Local Magnetic Field Measurements: Sources of Error," Meas. Sci. Technol., vol. 21, no. 10, October 2010.
[52] S. Tumanski, "Induction Coil Sensors - A Review," Meas. Sci. Technol., vol. 18, pp. R31-R46, 2007.
[53] Y. Li, Q. Yang, Y. Liu, Z. Zhao, C. Zhang and D. Li, "A Novel Combined B−H Sensing Coil in Three-Dimensional Magnetic Properties Testing System," IEEE trans. Applied Supercond., vol. 24, no. 3, 2014.
[54] F. Fiorillo and A. Rietto, "Extended Induction Range Analysis of Rotational Losses in Soft Magnetic Materials," IEEE Trans. Magn., vol. 24, no. 2, pp. 1960-1962, March 1988.
[55] A. M. Gumaidh, T. Meydan and A. Moses, "Characterisation of Magnetic Materials Under Two-dimensional Excitation," in IEEE Digest of International Magnetics Conference 1993 (INTERMAG 93), 1993.
[56] J. Sievert et al, "Intercomparison of Measurements of Magnetic Losses in Electrical Sheet Steel Under Rotating Flux Conditions," Director General XII Science, Research and Development, EC Brussels, 1995.
[57] A. Moses, "Possible Future Trends and Research Challenges Realted to 1 & 2D Magentic Properties of Soft Magentic Matarials," Przeglad Elecktrotechniczny (Electrical Review), vol. R.87, no. 9b, pp. 11-16, 2011.
[58] G. Krismanic, "Recent Developments and Trends in Measurements of Two-Dimensional Magentic Properties," J. Elect. Eng., vol. 55, no. 10, pp. 45-48, 2004.
[59] JSOL Corporation, "Techical Support & User's Manual Solver for JMAG Designer Version 12," 2013.
[60] H. Soltner and P. Blumer, "Dipolar Halbach Magnet Stacks Made from Identically Shaped Permanent Magnets for Magnetic Resonance," Concepts Magn. Reson. Part A, vol. 36A, no. 4, pp. 211-222, 2010.
[61] V. Gorican, A. Hamler, M. Jesenik, B. Stumberger and M. Trlep, "Unrealiable Determination of Vector B in 2-D SST," J. Magn. Magn. Mater., Vols. 254-255, pp. 130-132, January 2003.
[62] J. Zhong and J. Zhu, "Improved Measurement With 2-D Rotating Fluxes Considering the Effect of Internal Field," IEEE Trans. Magn., vol. 41, no. 10, pp. 3709-3711, 2005.
[63] Asahi Kasei Microdevices, "EQ-730L data sheet," [Online]. Available: http://www.akm.com/akm/en/file/datasheet/EQ-730L.pdf. [Accessed 19 Dec 2014].
[64] J. E. Parks, "Helmholtz Coils-Uniform Magnetic Fields," Department of Phyics and Astronomy, The University of Tennessee, Knoxville, 2013.
[65] M. Enokizono and J. Sievert, "Numerical Analysis of Accuracy of rotational Magnetic Loss Measurement Apparatus," IEEE Trans. Magn. Japan, vol. 5, no. 9, pp. 742-748, September 1990.
[66] J. Wanjiku and P. Pillay, "Design Considerations of 2-D Magnetizers for High Flux Density Measurements," IEEE Trans. Indu. Applicat., vol. 51, no. 5, pp. 3629-3638, 2015.
[67] Y. Li, Q. Yang, J. G. Zhu and Y. Guo, "Magnetic Properties Measurement of Soft Magnetic Composite Materials Over Wide Range of Excitation Frequency," IEEE Trans. Indu. Applicat., vol. 48, no. 1, pp. 88-97, 2012.
[68] S. Zurek and T. Meydan, "Errors in the Power Loss Measured in CW and ACW Rotational Magnetisation. Part 2: Physical Phenomena," IEE Proc.-Sci. Meas. Technol., vol. 153, no. 4, pp. 152-157, 2006.
[69] M. Dimitre, M. Rauch, M. D. Wulf and J. Melkebeek, "Accurate Field Strength Measurement in Rotational Single Sheet Testers," J. Magn. Magn. Mater., pp. 673-676, 2000.
[70] M. Jesenik, V. Gorican, M. Trlep, A. Hamler and B. Stumberger, "Field Homogeneity in a Two-phase Round Rotational Single Sheet Tester With One and Both Side Sheilds," J. Magn. Magn. Mater., Vols. 254-255, pp. 247-249, 2003.
[71] V. Gorican, A. Hamler, M. Jesenik, B. Stumberger and M. Trlep, "Interaction of z component of magnetic field between two samples of GO material in the round rotational single sheet tester," J. Magn. Magn. Mater., vol. 304, pp. 558-560, 2006.
[72] ASTM Committee on Magnetic Properties, "Standard Practice for Sampling and Procurement Testing of Magnetic Materials," ASTM International, 2001.
[73] ASTM Committee on Magnetic Properties, "Standard Test Method for Alternating-Current Magnetic Properties of Toroidal Core Specimens Using the Voltmeter-Ammeter-Wattmeter Method," ASTM International, 1999.
[74] S. G. Rabinovich, Measurement Errors and Uncertainties: Theory and Practice, Springer, 2005.
[75] A. Ferrero and S. Salicone, "Modeling and Processing Measurement Uncertainty Within the Theory of Evidence: Mathematics of Random-Fuzzy Variables," IEEE trans. Instrumentation and Measurement, vol. 56, no. 3, pp. 704-716, 2007.
[76] N. Ridler, B. Lee, J. Martens and K. Wong, "Measurement Uncertainty, Traceability, and the GUM," IEEE Microwave Magazine, vol. 8, no. 4, pp. 44-53, 2007.
[77] A. Giordani and L. Mari, "Measurement, models, and uncertainty," IEEE trans. Instrumentation and Measurement, vol. 61, no. 8, pp. 2144-2152, 2012.
[78] R. Furness, "The cost of measurement uncertainty," in IEEE Petroleum and Chemical Industry Conference Europe (PCIC Europe), 2008.
[79] G. Beges, J. Drnovsek, I. Pusnik and J. Bojkovski, "Calculation and proper presentation of the measurement uncertainty in testing," in 19th IEEE Instrumentation and Measurement Technology Conference (IMTC), 2002.
[80] J. Wirandi, W. Kulesza and A. Lauber, "Modeling of Industrial Measurement Systems Considering the Human Factor," in IEEE Instrumentation and Measurement Technology Conference (IMTC), 2006.
[81] B. Lu, W. Cao and T. Habetler, "Error Analysis of Motor-Efficiency Estimation and Measurement," in IEEE Power Electronics Specialists Conference, 2007.
[82] Joint Committee for Guides in Metrology, "Evaluation of measurement data — Guide to the expression of uncertainty in measurement," JCGM, 2008.
[83] Joint Committee for Guides in Metrology, "Evaluation of measurement data - Supplement 1 to the GUM - Propagation of distributions using a Monte Carlo method," JCGM, 2008.
[84] A. Ferrero and S. Salicone, "A Comparative Analysis of the Statistical and Random-Fuzzy Approaches in the Expression of Uncertainty in Measurement," IEEE trans. Intrumentation and Measurement, vol. 54, no. 4, pp. 1475-1481, 2005.
[85] T. Lovett, F. Ponci and A. Monti, "A polynomial chaos approach to measurement uncertainty," IEEE trans. Instrumentation and Measurement, vol. 55, no. 3, pp. 729-736, 2006.
[86] D. Lampasi, F. Nicola and L. Podesta, "Generalized lambda distribution for the expression of measurement uncertainty," IEEE trans. Instrumentation and Measurement, vol. 55, no. 4, pp. 1281-1287, 2006.
[87] L. Angrisani, R. Moriello and M. D'Apuzzo, "New proposal for uncertainty evaluation in indirect measurements," IEEE trans. Instrumentation and Measurement, vol. 55, no. 4, pp. 1059-1064, 2006.
[88] P. Memmolo, L. Moriello, R. Schiano and P. Pinto, "On the Use of Numeric Integration for Uncertainty Evaluation in Indirect Measurements," in IEEE International Workshop on Advanced Methods for Uncertainty Estimation in Measurement, 2007.
[89] P. Hack, T. Caten and C. Schwengber, "Measurement uncertainty: Literature review and research trends," IEEE trans. Instrumentation and Measurement , vol. 61, no. 8, pp. 2116-2124, 2012.
[90] G. Cipriani, D. La Cascia, R. Miceli and C. Spataro, "Uncertainty management in the measurements for the electric power quality analysis," in IEEE International Energy Conference (ENERGYCON), 2014.
[91] A. Ferrero and S. Salicone, "The Random-Fuzzy Variables: A New Approach to the Expression of Uncertainty in Measurement," IEEE trans. Instrumentation and Measurement, vol. 53, no. 5, pp. 1370-1377, 2004.
[92] S. Sona and M. Havlikova, "Comparison of GUM and Monte Carlo method for evaluation measurement uncertainty of indirect measurements," in 14th IEEE International Carpathian Control Conference, 2013.
[93] S. Nuccio and C. Spataro, "A Monte Carlo method for the auto‐evaluation of the uncertainties in the analog‐to‐digital conversion‐based measurements," The international journal for computation and mathematics in electrical and electronic engineering, vol. 23, no. 1, pp. 148-158, 2004.
[94] K. Barbé, L. Gonzales Fuentes, O. Olarte and L. Lauwers, "Monte-Carlo parameter uncertainty analysis under dynamical and operational measurement conditions," in IEEE International Instrumentation and Measurement Technology Conference (I2MTC), 2014.
[95] B. Hall, "Calculations of measurement uncertainty in complex-valued quantities involving'uncertainty in the uncertainty'," in IEEE ARFTG Microwave Measurements Conference, 2004.
[96] A. Ferrero, M. Prioli and S. Salicone, "Processing dependent systematic contributions to measurement uncertainty," IEEE trans. Instrumentation and Measurement, vol. 62, no. 4, pp. 720-731, 2013.
[97] A. Smith, A. Monti and F. Ponci, "Uncertainty and worst-case analysis in electrical measurements using polynomial chaos theory," IEEE trans. Instrumentation and Measurement, vol. 58, no. 1, pp. 58-67, 2009.
[98] J. Kohler and L. Gradin, "Test laboratory position for expression of uncertainty and confidence in measurement," in IEEE International Symposium on Electromagnetic Compatibility, 2003.
[99] H. Ahlers and J. Ludke, "The uncertainties of magnetic properties measurements of electrical sheet steel," J. Magn. Magn. Mater., vol. 215, pp. 711-713, 2000.
[100] M. S. Pierce and et al, "Disorder-induced magnetic memory: Experiments and theories," Physical Review, vol. B, no. 75, 2007.
[101] Y. Ishihara, A. Isozumi, T. Todaka and T. Nakata, "Comparison of two averaging methods for improving the measurement accuracy of power loss," J. Magn. Magn. Mater., vol. 215, pp. 696-699, 2000.
[102] dSPACE GmbH, "DS1103 PPC Controller Board," in dSPACE Catalog 2015, pp. 334-338.
[103] S. A. More, "ADC Performance Parameters," Texas Instruments , 2013.
[104] N. Alatawneh and P. Pillay, "Design of a Novel Test Fixture to Measure Rotational Core losses in Machine Laminations," IEEE Trans. on Industrial Applications, vol. 48, no. 5, 2012.
[105] V. Gorican, M. Jesenik, A. Hamler, B. Stumberger and M. Trlep, "Measurement of 2-D Magnetic Properties of Grain Oriented Silicon Steel Sheet Using RRSST," in 11th International Symposium on Electromagnetic Fields in Electrical Engineering (ISEF 2003), Maribor, Slovenia, September, 2003.
[106] Y. Maeda, H. Shimoji, T. Todaka and M. Enokizono, "Study of the Counterclockwise/Clockwise (CCW/CW) Rotational Losses Measured with a Two-Dimensional Vector Magnetic Property Mesurement System," IEEJ Trans. Elect. Elect. Eng., vol. 3, pp. 222-228, 2008.
[107] Coyote Steel & Co., "Resources: ASTM/AISI Thickness Tolerance Ranges," [Online]. Available: http://www.coyotesteel.com/resources_toleranceranges.shtml. [Accessed 29 July 2015].
[108] M. M. Znidarich, "Upgrading and Uprating of Hydro Generators: An Australian Perspective," Australian Journal of Electrical and Electronics Engineering, vol. 10, no. 1, pp. 75-84, 2015.
All items in Spectrum are protected by copyright, with all rights reserved. The use of items is governed by Spectrum's terms of access.

Repository Staff Only: item control page

Downloads per month over past year

Research related to the current document (at the CORE website)
- Research related to the current document (at the CORE website)
Back to top Back to top