Login | Register

Winding Function Modeling of Synchronous Reluctance Machines

Title:

Winding Function Modeling of Synchronous Reluctance Machines

Maroufian, Seyede Sara (2018) Winding Function Modeling of Synchronous Reluctance Machines. PhD thesis, Concordia University.

[thumbnail of Maroufian_PhD_S2019.pdf]
Preview
Text (application/pdf)
Maroufian_PhD_S2019.pdf - Accepted Version
Available under License Spectrum Terms of Access.
6MB

Abstract

The current electric vehicle market, as well as many other industrial applications, is heavily focused on the application of permanent magnet (PM) machines and induction machines (IM). However the limitations of these two types of electric machines reveal the necessity for further research in the field of electrical machines to substitute the existing types with less expensive, and more fault tolerant machines. The synchronous reluctance machine (SynRM) is a singly excited machine with great potential to replace permanent magnet machines and induction machines in traction, as well as many other industrial applications. The rotor structure is simple and only made of steel laminations, which makes the manufacturing procedure less expensive compared to PM machines and IMs. Moreover the absence of rotor windings and a rotor cage eliminates the rotor copper loss, thus enhancing the efficiency compared to IMs. However, the use of the SynRM has not yet reached the same maturity level of its counterparts and still faces problems like low power density, poor power factor, and limited torque-speed envelope, representing a fertile terrain for research.
The aim of this research is to develop an analytical approach based on the winding function method for modeling, analysis, and design of SynRMs and PM assisted SynRMs. The proposed analytical approach is based on the winding configuration of the machine, and the magnetic characteristics of the rotor topology. It provides insight of the machine’s characteristics, and can be used to apply design modifications on existing SynRMs to improve the performance of future designs. The analytical model is later modified for designing a PM assisted SynRM using AlNiCo magnets, with the aim to improve the power factor and torque density of the regular SynRM.
The self-excitation phenomenon in synchronous reluctance generators (SynRGs) is also investigated and the requirements for the assurance of self-excitation are identified. Therefore in traction applications, and electric vehicles with vehicle to grid (V2G) capability, the possibility of utilizing the onboard SynRM as a power generation unit for emergency situations can be considered. The stand-alone SynRG can also be used as a fault tolerant power generation unit to supply electric power in remote areas.

Divisions:Concordia University > Gina Cody School of Engineering and Computer Science > Electrical and Computer Engineering
Item Type:Thesis (PhD)
Authors:Maroufian, Seyede Sara
Institution:Concordia University
Degree Name:Ph. D.
Program:Electrical and Computer Engineering
Date:1 August 2018
Thesis Supervisor(s):Pillay, Pragasen
Keywords:Winding function, synchronous reluctance machine, permanent magnets, permanent magnet assisted synchronous reluctance machine, synchronous reluctance generator, self-excitation
ID Code:984658
Deposited By: SEYEDE SARA MAROUFIAN
Deposited On:10 Jun 2019 15:03
Last Modified:10 Jun 2019 15:03

References:

[1] B. Kramer, S. Chakrabotry and B. Kroposki, "A Review of Plug-in Vehicles and Vehicle-to-Grid Capability," in Industrial Electronics, 2008. IECON 2008. 34th Annual Conference of IEEE, Orlando, FL, 2008.
[2] R. G. Gago, S. F. Pinto and J. F. Silva, "G2V and V2G Electric Vehicle Charger for Smart Grids," in IEEE International Smart Cities Conference (ISC2), Trento, Italy, 2016.
[3] X. Zhang, Q. Wang and G. Xu, "A review of Plug-in Electric Vehicles as Distributed Energy Storages in Smart Grid," in 5th IEEE OES Innovative Smart Grid Technologies Europe, Istanbul, 2014.
[4] F. Laureri, L. Puliga, M. Robba, F. Defino and G. Odena Bulto, "An Optimization Model for the Integration of Electric Vehicles and Smart Grids: Problem Definition and Experimental Validation," in IEEE International Smart Cities Conference (ISC2), Trento, Italy, 2016.
[5] S. Taghavi, Design of Synchronous Reluctance Machines for Automotive Applications, Montreal, QC, Canada: A Thesis in the Department of Electrical and Computer Engineering, Concordia University, Montreal, Canada, 2015.
[6] S. Taghavi and P. Pillay, "A Sizing Methodology of the Synchronous Reluctance Motor for Traction Applications," IEEE Journal of Emerging and Selected Topics in Power Electronics, vol. 2, no. 2, pp. 329-340, June 2014.
[7] A. Vagati, "The Synchronous Reluctance Solution: A New Alternative in AC Drives," in Industrial Electronics, Control and Instrumentation, 1994. IECON '94., 20th International Conference on, Bologna, 5-9 Sep 1994.
[8] A. Alolah, "Steady-State Operating Limits of Three Phase Self-Excited Reluctance Generator," Generation, Transmission and Distribution, IEE Proceedings C, vol. 139, no. 3, pp. 261-268, May 1992.
[9] S. Taghavi and P. Pillay, "A Comparative Study of Synchronous Reluctance Machine Performance with Different Pole Numbers for Automotive Applications," in Industrial Electronics Society, IECON 2014 - 40th Annual Conference of the IEEE, Dallas, TX, 2014.
[10] T. Matsuo and T. A. Lipo, "Rotor Design Optimization of Synchronous Reluctance Machine," IEEE Transactions on Energy Conversion, vol. 9, no. 2, pp. 359-365, June 1994.
[11] D. Staton, T. Miller and S. Wood, "Maximising the saliency Ratio of the Synchronous Reluctance Motor," Electric Power Applications, IEE Proceedings B, vol. 140, no. 4, pp. 249-259, July 1993.
[12] ABB, ABB, 2016. [Online]. Available: http://new.abb.com/motors-generators/iec-low-voltage-motors/frequency-controlled-motors/synchronous-reluctance-motor-drive-packages/synrm-verified-package-efficiency. [Accessed 2017].
[13] E. Obe, "Calculation of inductances and torque of an axially laminated synchronous reluctance motor," IET Electric Power Application, vol. 4, no. 9, pp. 783-792, December 2009.
[14] A. Ogunjuyigbe, A. Jimoh, D. Nicolae and E. Obe, "Analysis of synchronous reluctance machine with magnetically coupled three-phase windings and reactive power compensation," IET Electric Power Applications, vol. 4, no. 4, pp. 291-303, 2009.
[15] A. Vagati, A. Canova, M. Pastorelli, M. Chiampi and M. Repetto, "Design Refinement of Synchronous Reluctance Motors Through Finite-Element Analysis," IEEE Transaction on Industry Applications, vol. 36, no. 4, pp. 1094-1102, July/August 2000.
[16] N. Bedetti, S. Calligaro and R. Petrella, "Stand-Still Self-Identification of Flux Characteristics for Synchronous Reluctance Machines Using Novel Saturation Approximating Function and Multiple Linear Regression," IEEE Trans. on Industry Applications, vol. 52, no. 4, pp. 3083-3092, 2016.
[17] N. Bianchi, S. Bolognani and D. Bon, "Rotor flux barrier design for torque ripple reduction in synchronous reluctance and PM-assisted synchronous reluctance motors," IEEE Trans. on industry applications, vol. 45, no. 3, pp. 921-928, 2009.
[18] Z. Azar and Z. Q. Zhu, "Performance Analysis of Synchronous Reluctance Machines Having Nonoverlapping Concentrated Winding and Sinusoidal Bipolar with DC Bias Excitation," IEEE Trans. on Industry Applications, vol. 50, no. 5, pp. 3346-3356, 2014.
[19] M. Palmieri, M. Perta and F. Cupertino, "Design of a 50.000 r/min Synchronous Reluctance Machine for an Aeronautic Diesel Engine Compressor," IEEE Trans. on Industry Apllications, vol. 52, no. 5, pp. 3831-3838, 2016.
[20] H. Kiriyama, S. Kawano, Y. Honda and T. Higaki, "High Performance Synchronous Reluctance Motor with Multi-flux Barrier for the appliance industry," in Industry Applications Conference, 1998. Thirty-Third IAS Annual Meeting. The 1998 IEEE , St. Louis, MO, Oct. 1998.
[21] I. Boldea, Z. Fu and S. Nasar, "Performance Evaluation of Axially-Laminated Anisotropic (ALA) Rotor Reluctance Synchronous Motors," in Industry Applications Society Annual Meeting, 1992., Conference Record of the 1992 IEEE, Houston, TX, Oct. 1992.
[22] A. Vagati, G. Franceschini, I. Marongiu and G. Troglia, "Design Criteria of High Performance Synchronous Reluctance Motors," in Industry Applications Society Annual Meeting, 1992., Conference Record of the 1992 IEEE, Houston, TX, Oct. 1992.
[23] M. Ibrahim, L. Masisi and P. Pillay, "Design of Variable-Flux Permanent-Magnet Machines Using Alnico Magnets," IEEE Transactions on Industry Applications, vol. 51, no. 6, pp. 4482-4491, 2015.
[24] Y. Wang, N. Bianchi, S. Bolonami and L. Alberti, "Synchronous Motors for Traction Applications," in Electrical and Electronic Technologies for Automotive, 2017 International Conference of, Torino, Italy, 2017.
[25] A. Vagati, A. Canova, M. Chiampi, M. Pastorelli and M. Repetto, "Desing refinement of synchronous reluctance motors through finite-element analysis," IEEE Trans. on Industry Applications, vol. 36, no. 4, pp. 1094-1102, 2000.
[26] S. Maroufian and P. Pillay, "Torque characterization of a synchronous reluctance machine using an analytical model," in Power Electronics, Drives and Energy Systems (PEDES), 2016 IEEE International Conference on, Trivandrum, India, 2016.
[27] G. Bacco and N. Bianchi, "Choice of Flux-barriers Position in Synchronous Reluctance Machines," in Energy Conversion Congress and Exposition (ECCE), 2017 IEEE, Cincinnati, OH, USA, 2017.
[28] M. Degano, H. Mahmoud, N. Bianchi and C. Gerada, "Synchronous reluctance machine analytical model optimization and validation through finite element analysis," in Electrical Machines (ICEM), 2016 XXII International Conference on, Lausanne, Switzerland, 2016.
[29] C. M. Spargo, B. C. Mecrow and J. D. Widmer, "A Seminumerical Finite-Element Postprocessing Torque Ripple Analysis Technique for Synchronous Electric Machines Utilizing the Air-Gap Maxwell Stress Tensor," IEEE Trans. on Magnetics, vol. 50, no. 5, p. 7026909, 2014.
[30] X. Luo, A. El-Antably and T. A. Lipo, "Multiple coupled circuit modeling of synchronous reluctance machines," in Industry Applications Society Annual Meeting, Denver, CO, 1994.
[31] M. Kamper, "Effect of rotor dimensions and cross magnetisation on Ld and Lq inductances of reluctance synchronous machine with cageless flux barrier rotor," Electric Power Applications, IEE Proceedings, vol. 141, no. 4, pp. 213-220, Jul 1994.
[32] M. N. Fathy Ibrahim, A. S. Abdel-khalik, E. E. M. Rashad and P. Sergeant, "An Improved Torque Density Synchronous Reluctance Machine with a Combined Star-Delta Winding Layout," IEEE Transactions on Energy Conversion, vol. 33, no. 3, pp. 1015-1024, 2018.
[33] Z. Yang and F. Tadashi, "Direct Output Power Control for PWM Converter-Based Super-High-Speed Reluctance Generator," IEEE Trans. on Industry Application, vol. 28, no. 1, pp. 57-63, 1992.
[34] R. Moncada, B. Pavez, J. Tapia and J. Pyrhonen, "Operation Analysis of Synchronous Reluctance Machine in Electric Power Generation," in International conference on electrical machines (ICEM), Berlin, Germany, 2014.
[35] W. s. Abu-Elhaija and A. Muetze, "self-Excitation and stability at speed transients of Self-Excited Single-Phase Reluctance Generators," IEEE Trnas. on Sustainable Energy, vol. 4, no. 1, pp. 136-144, 2013.
[36] Y. Rahim, J. Fletcher and N. Hassanian, "Performance Analysis of Salient-Pole Self-Excited Reluctance Generators Using a Simplified Model," IET Renewable Power Generation, vol. 4, no. 3, pp. 253-260, 2010.
[37] A. Alolah, "Steady-state operating limits of three phase self-excited reluctance generator," IEE proceeding C generation and transmission, vol. 139, no. 3, pp. 261-268, 1992.
[38] S. Guha and N. C. Kar, "Saturation Modeling and Stability Analysis of Synchrnous Reluctance Generator," IEEE Trans. on Energy conversion, vol. 23, no. 3, pp. 814-823, 2008.
[39] N. Eldeen, A. M. Hassanian, A. Y. M. Abbas and A. S. G. Hussien, "Performance Analysis of Isolated Self-Excited Reluctance Generators. Connected to Diode Bridge Rectifier," SUST journal of engineering and computer science (JESC), vol. 16, no. 3, pp. 1-18, 2015.
[40] M. Anajjar and D. Gerling, "Synchronous Reluctance Generator with FPGA Control of Three-Level Neutral-Point-Clamped Converter for Wind Power Application," in Power Electronics and Motion Control Conference (PEMC), 2016 IEEE International, Varna, Bulgaria, 2016.
[41] A. E. Hoffer, R. H. Moncada, B. J. Pavez, J. A. Tapia and L. Laurila, "A High Efficiency control Strategy for Synchronous Reluctance Generator Including Saturation," in XXII International Conference on Electrical Machines (ICEM), Lausanne, Switzerland, 2016.
[42] T. Fukao, Z. Yang and M. Matsui, "Voltage Control of Super High-Speed Reluctance Generator System with a PWM Voltage Source Converter," IEEE Trans. on Industry Applications, vol. 28, no. 4, pp. 880-886, 1992.
[43] M. Bodson and O. Kiselychnyk, "Analysis of triggered self-excitation in induction generators and experimental validation," IEEE transactions on energy conversion , vol. 27, no. 2, pp. 238-249, 2012.
[44] M. Bodson and O. Kiselychnyc, "On the triggering of self-excitation in induction generators," in International symposium of power electronics, electrical drives automation and motion (SPEEDAM), Pisa, Italy, 2010.
[45] Y. Rahim, A. Mohamadien and A. Al Khalaf, "Comparison between the Steady-State performance of Self-Excited Reluctance and Inducion Generators," IEEE Trans. on Energy Conversion, vol. 5, no. 3, pp. 519-525, 1990.
[46] Y. Tan, K. M. Muttaqi, L. Meegahapola and P. Ciufo, "Deadband Control of Doubly-Fed Induction Generator Around Synchrnous Speed," IEEE Trans. on energy Conversion, vol. 31, no. 4, pp. 1610-1621, 2016.
[47] O. Ojo and W. Zhiqing, "Synchronous operation of a dual-winding reluctance generator," IEEE transactions on energy conversion, vol. 12, no. 4, pp. 357-362, 1997.
[48] I. Boldea, Z. Fu and S. Nasar, "High performance synchronous reluctance generator," IEE proceeding B electric power applications, vol. 140, no. 2, pp. 124-130, 1993.
[49] M. E. Baran and A. J. Goetze, "Equivalent Circuits of AC Machines Based on Field Analyis," IEEE Trans. on Power Systems, vol. 9, no. 2, pp. 565-572, 1994.
[50] V. Ostovic, Dynamics of Saturated Electric Machines, New York: Springer-Verlag Inc., 1989.
[51] M. Amrhein and P. T. Krein, "Force Calculation in 3-D Magnetic Equivalent Circuit Networks with a Maxwell Stress Tensor," IEEE Trans. on Energy Conversion, vol. 24, no. 3, pp. 587-593, 2009.
[52] A. J. Pina, Y. Alsmadi and L. Xu, "Analytical Model for the Minimization of Torque Ripple in Permanent Magnets Assisted Synchronous Reluctance Motors Through Asymmetric Rotor Poles," in Energy Conversion Congress and Exposition (ECCE), Montreal, QC, Canada, 2015.
[53] T. Lipo, Analysis of Synchrnous Machines, Second edition, Boca Raton, FL: CRC Press, Taylor and Francis Group, 2012.
[54] N. A. Al Nuaim and H. Toliyat, "A Method for Dynamic Simulation and Detection of Dynamic Air gap Eccentrcicity in Synchronous Machines," in IEEE International Electric Machines and Drives, Milwaukee, WI, USA, 1997.
[55] R. Qu and T. Lipo, "General Closed-Form Analytical Expressions for Air gap Inductances for surface-mounted Permanent Magnet and Induction Machines," in IEEE International Electric Machines and Drives Conference, Madison, WI, USA, 2003.
[56] O. Ojo, A. Ginart, O. Omozusi and A. Jimoh, "Modeling and Analysis of a Single-Phase Synchronous Reluctance Machine Including Saturation Effect," in IEEE Industry Application Society Annual Meeting, New Orleans, Louisiana, USA, 1997.
[57] I. Sadeghi, H. Ehya and J. Faiz, "Analytic method for eccentricity fault diagnosis in salient-pole synchronous generators," in International Conference on Optimization of Electrical and Electronic Equipment (OPTIM) & 2017 Intl Aegean Conference on Electrical Machines and Power Electronics (ACEMP), Brasov, Romania, 2017.
[58] I. Boldea, Reluctance Synchronous Machines and Drives, Oxford: Clarendon press, 1996.
[59] N. Bianchi and B. Chalmers, "Axially Laminated Reluctance Motor: Analytical and Finite-Element Methods for Magnetic Analysis," IEEE Trans. on Magnetics, vol. 38, no. 1, pp. 239-245, 2002.
[60] S. Taghavi and P. Pillay, "A Novel Grain-Oriented Lamination Rotor Core Assembly for a Synchronous Reluctance Traction Motor With a Reduced Torque Ripple Algorithm," IEEE Trans. on Industry Applications, vol. 52, no. 5, pp. 3729-3738, 2016.
[61] K. J. Meessen, J. J. H. Paulides and E. A. Lomonova, "Force Calculation in 3-D Cylindrical Structures Using Fourier Analysis and the Maxwell Stress Tensor," IEEE Trans. on Magnetics, vol. 49, no. 1, pp. 536-545, 2013.
[62] H. VuXuan, D. Lahaye, S. Ani, H. Polinder and J. Ferreira, "Effect of Design Parameters on Electromagnetic Torque of PM Machines with Concentrated Windings Using Nonlinear Dynamic FEM," in IEEE International Electric Machines and Drives Conference (IEMDC), Niagra Falls, ON, 2011.
[63] N. Bianchi, E. Fornasiero and W. Soong, "Optimal Selection of PM Flux Linkage in a PM Assisted Synchronous Reluctance Machine," in Electrical Machines (ICEM), Berlin, Germany, 2014.
[64] J. Kitao, Y. Takahashi, K. Fujiwara, A. Ahgon, t. Matsuo and A. Daikoku, "Input and Output Power in Finite-Element Analysis of Electric Machines Taking Account of Hysteretic Property," IEEE Trans. on Magnetics, vol. PP, no. 99, pp. 1-4, 2017.
[65] A. Takbash, M. Ibrahim and P. Pillay, "Torque ripple reduction of a variable flux motor," in Energy Conversion Congress and Exposition (ECCE), 2016 IEEE, Milwaukee, WI, USA, 2016.
[66] S. Mishara, T. A. Lipo and S. V. Pamidi, "Design and analysis of a novel brushlesshigh temperature superconducting synchronous machine," in Electric Machines and Drives Conference (IEMDC), 2017 IEEE International, Miami, FL, USA, 2017.
[67] S. Taghavi and P. Pillay, "A Novel Grain-Oriented Lamination Rotor Core Assembly for a Synchronous Reluctance Traction Motor with a Reduced Torque Ripple Algorithm," IEEE Trans. on Industry Applications, vol. 52, no. 5, pp. 3729-3738, 2016.
[68] H. Cai, B. Guan and L. Xu, "Low-Cost Ferrite PM-Assisted Synchronous Reluctance Machine foe Electric Vehicles," IEEE Trans. on Industrial Electronics, vol. 61, no. 10, pp. 5741-5748, 2014.
[69] M. Barcaro, T. Pradella and I. Furlan, "Low-Torque Ripple Design of a Ferrite-Assisted Synchronous Reluctance Motor," IET Electric Power Applications, vol. 10, no. 5, pp. 319-329, 2015.
[70] N. Bianchi, S. Bolognani, D. Bon and M. Dai Pre, "Torque Harmonic Compensation in a Synchronous Reluctance Motor," IEEE Trans. on Energy Conversion, vol. 23, no. 2, pp. 466-473, 2008.
[71] H. Cong Liu, I.-G. Kim, Y. Jun Oh, J. Lee and S.-C. Go, "Design of Permanent Magnet-Assisted Synchronous Reluctance Motor for Maximized Back-EMF and Torque Ripple Reduction," IEEE Trans. on Magnetics, vol. 53, no. 6, pp. 1-4, 2017.
[72] T. A. Huynh and M.-F. Hsieh, "Comparative Study of PM-Assisted SynRM and IPMSM on Constant Power Speed Range for EV Applications," IEEE Transaction on Magnetics, vol. 53, no. 11, pp. 1-6, 2017.
[73] Y. Wang, G. Bacco and N. Bianchi, "Geometry Analysis and Optimization of PM-Assisted Reluctance Motors," IEEE Transaction on Industry Applications, vol. 53, no. 5, pp. 4338-4347, 2017.
[74] P. Guglielmi, G. Giraudi, G. Pellegrino and A. Vagati, "P.M. Assisted Synchronous Reluctance Drive for Minimal Hybrid Application," in Conference Record of the 2004 IEEE Industry Applications Conference, 2004. 39th IAS Annual Meeting., Seattle, WA, USA, 2004.
[75] M. Gamba, G. Pellegrino and A. Vagati, "A New PM-Assisted Synchronous Reluctance machine with a nonconventional fractional slot per pole combination," in Optimization of Electrical and Electronic Equipment (OPTIM), 2014 International Conference on, Bran, Romania, 2014.
[76] W. Zhao, F. Xing, X. Wang, T. A. Lipo and B.-i. Kwon, "Design and Analysis of a Novel PM-Assisted Synchronous Reluctance Machine with Axially Integrated Magnets by the Finite-Element Method," IEEE Trans. on Magnetics, vol. 53, no. 6, 2017.
[77] N. Bianchi, E. Fornasiero, M. Ferrari and M. Castiello, "Experimental Comparison of PM-Assisted Synchronous Reluctance Motors," IEEE Trans. on Industry Applications, vol. 52, no. 1, pp. 163-171, 2016.
[78] M. Barcaro and N. Bianchi, "Interior PM Machines using Ferrite to Substitute Rare–Earth Surface PM Machines," in International conference on Electrical Machines (ICEM), Marseille, France, 2012.
[79] R. Lohninger, H. Grabner, G. Weidenholzer, S. Silber and W. Amrhein, "Modeling, simulation, and Design of a Permanent Magnet Assisted Synchronous Reluctance Machine," IEEE Transaction on Industry Applications, vol. 51, no. 1, pp. 196-203, 2015.
[80] J. Baek, S. S. Reddy Bonthu, S. Kwak and S. Choi, "Optimal design of five-phase permanent magnet assisted synchronous reluctance motor for low output torque ripple," in Energy Conversion Congress and Exposition (ECCE), 2014 IEEE, Pittsburgh, PA, USA, 2014.
[81] M. T. Bin Tarek and S. Choi, "Design and rotor shape modification of a multiphase high speed permanent magnet assisted synchronous reluctance motor for stress reduction," in Energy Conversion Congress and Exposition (ECCE), 2017 IEEE, Cincinnati, OH, USA, 2017.
[82] D. C. Hanselman, Brushless Permanent-Magnet Motor Design, Orono, Maine: McGraw-Hill, Inc., 1994.
[83] T. J. E. Miller, Brushless Permanent Magnet and Reluctance Motor Drives, New York: Clarendon Press OXFORD, 1989.
[84] O. Ojo, "Limit-Cycle and Small Signal Dynamics of Self-Excited Snchronous Reluctance Generator," in 26th southeastern Symposium of System Theory, Athens, Ohio, USA, 1994.
[85] O. Ojo, G. Dong and M. Osaretin Omoigui, "Analysis of a Synchronous Reluctance Machine with an Auxiliary Single-Phase Winding," IEEE Transaction of Industry Applications, vol. 39, no. 5, pp. 1307-1313, 2003.
[86] S. Maroufian and P. Pillay, "Self-excitation criteria of the synchronous reluctance generator in stand-alone mode of operation," in IEEE International Conference on Power Electronics, Drives and Energy Systems (PEDES), Trivandrum, India, 2016.
[87] S. S. Maroufian and P. Pillay, "Self-Excitation Criteria of the Synchronous Reluctance Generator in Stand-Alone Mode of Operation," IEEE Transactions on Industry Applications, vol. 54, no. 2, pp. 1245-1253, 2018.
[88] M. Bodson and O. Kiselynchynk, "On the Capacitor Voltage Needed to Trigger Self-Excitation in Induction Generators," in 19th Mediterranean Conference on control and Automation, Pisa, Italy, 2011.
[89] Y. Zhang, P. Pillay, M. Ibrahim and M. C. Cheng, "Magnetic characteristic and core losses in machine laminations: high frequency loss prediction from low frequency measurements," IEEE transactions on industry applications, vol. 48, no. 2, pp. 623-629, 2011.
[90] H. Hauser, Y. Melikhov and D. C. Jiles, "Examination of the equivalence of ferromagnetic hysteresis models describing the dependence of magnetization on magnetic field and stress," IEEE Transaction on Magnetics, vol. 45, no. 2, pp. 1940-1949, 2009.
[91] Y. Wang and N. Bianchi, "Investigation of Self-Excited Synchronous Reluctance Generators," IEEE Transaction on Industry Applications, vol. 54, no. 2, pp. 1360-1369, 2017.
All items in Spectrum are protected by copyright, with all rights reserved. The use of items is governed by Spectrum's terms of access.

Repository Staff Only: item control page

Downloads per month over past year

Research related to the current document (at the CORE website)
- Research related to the current document (at the CORE website)
Back to top Back to top