Alahdal, Abdulelah (2024) In-plane Cyclic Response of Flexural-Dominated Partially Grouted Reinforced Masonry Shear Walls with Boundary Elements. PhD thesis, Concordia University.
Preview |
Text (application/pdf)
15MBAlahdal_PhD_F2024.pdf - Accepted Version Available under License Spectrum Terms of Access. |
Abstract
Reinforced masonry shear walls (RMSWs) are commonly used in seismic regions, but predicting their behaviour is challenging due to the composite nature of materials like masonry blocks, mortar, steel rebars, and grout. This complexity is heightened in partially grouted (PG) walls, where stiffness discontinuities occur at interfaces between grouted and ungrouted cells. The scarcity of experimental data on the materials’ properties has further complicated the development of accurate analytical models.
This research aims to enhance the lateral performance of PG masonry shear walls and develop a reliable analytical model. The study is divided into two main Phases: analytical and experimental. In the analytical phase (Phase I), a nonlinear finite element model was developed and validated against experimental data from the literature. Due to the lack of material properties in existing studies, assumptions were made to fill these gaps. The model generated a comprehensive matrix of 196 numerical models, covering a wide range of parameters such as aspect ratio, spacing between grouted cells, axial load, reinforcement ratios, and grouted and ungrouted compressive strengths. In the experimental phase (Phase II), 84 masonry prisms were tested to evaluate the compressive, shear, and tensile properties of grouted, ungrouted, and boundary element masonry assemblages. Consequently, using these components, two half-scale PG shear wall specimens with C-shaped boundary elements were constructed and tested under high axial loads and in-plane cyclic loading. These tests represented the lower storey of RMSWs in of a six- and twelve-storey buildings and examined the impact of full versus partial grouting and aspect ratios.
The analytical investigation resulted in three penta-linear load-displacement backbone models for flexural-dominated, shear-dominated, and combined failure modes, along with secant stiffness expressions for each wall type. These models were validated against additional data, showing good accuracy for PG walls. The study also identified the inadequacy of the stiffness reduction factor in CSA S304-14 for PG walls, leading to the derivation of new coefficients. The experimental results provided detailed stress-strain data for various mechanical properties, and wall tests showed ductile performance with high energy dissipation, exceeding North American design standards before strength degradation began.
| Divisions: | Concordia University > Gina Cody School of Engineering and Computer Science > Building, Civil and Environmental Engineering |
|---|---|
| Item Type: | Thesis (PhD) |
| Authors: | Alahdal, Abdulelah |
| Institution: | Concordia University |
| Degree Name: | Ph. D. |
| Program: | Civil Engineering |
| Date: | 15 July 2024 |
| Thesis Supervisor(s): | Galal, Khaled |
| Keywords: | Masonry shear walls, fully grouted, partially grouted, cyclic loading, boundary elements |
| ID Code: | 994439 |
| Deposited By: | Abdulelah Mansoor Mohammed Alahdal |
| Deposited On: | 24 Oct 2024 16:06 |
| Last Modified: | 06 Nov 2024 18:57 |
References:
ABAQUS. (2013). 6.13-3. RI Abaqus analysis user’s manual. USA: Dassault Systems Providence.AbdAllah, A. R., AbdelRahman, B., Galal, K. (2023). Numerical study of the seismic performance of fully grouted reinforced masonry shear walls with boundary elements subjected to dynamic loading. Engineering Structures, 295(July), 116804. https://doi.org/10.1016/j.engstruct.2023.116804
AbdelRahman, B., Galal, K. (2020). Influence of pre-wetting, non-shrink grout, and scaling on the compressive strength of grouted concrete masonry prisms. Construction and Building Materials, 241, 117985. https://doi.org/10.1016/j.conbuildmat.2019.117985
Ahmad, S. H., Xie, Y., Yu, T. (1995). Shear ductility of reinforced lightweight concrete beams of normal strength and high strength concrete. Cement and Concrete Composites, 17(2), 147–159. https://doi.org/10.1016/0958-9465(94)00029-X
Albutainy, M., Galal, K. (2021). Experimental investigation of reinforced concrete masonry shear walls with C-shaped masonry units boundary elements. Structures, 34(October), 3667–3683. https://doi.org/10.1016/j.istruc.2021.09.080
Albutainy, M., Galal, K. (2024). Effect of boundary element detailing on the seismic performance of reinforced concrete masonry shear walls. Engineering Structures, 300(January 2023), 117164. https://doi.org/10.1016/j.engstruct.2023.117164
Albutainy, M. L. (2016). Seismic Performance of Ductile Reinforced Concrete Masonry Shear Walls with C-Shaped Boundary Elements. Ph.D. Thesis, Building, Civil, and Environmental Engineering, Concordia University, Montreal, Quebec, Canada. Retrieved from https://medium.com/@arifwicaksanaa/pengertian-use-case-a7e576e1b6bf
Alecci, V., Fagone, M., Rotunno, T., De Stefano, M. (2013). Shear strength of brick masonry walls assembled with different types of mortar. Construction and Building Materials, 40, 1038–1045. https://doi.org/10.1016/j.conbuildmat.2012.11.107
Almeida, J. C., Lourenço, P. B., Barros, J. (2002). Characterization of masonry under uniaxial tension. In VII International Seminar on Structural Masonry for Developing Contries (p. 24). Belo Horizonte, Brazil. Retrieved from http://www.civil.uminho.pt/masonry/Publications/2002_Lourenco_et_al.pdf
Aly, N. E. (2019). Seismic performance and height limits of ductile reinforced masonry shear wall buildings with boundary elements. Ph.D. Thesis, Building, Civil, and Environmental Engineering, Concordia University, Montreal, Quebec, Canada. https://doi.org/10.1016/j.engstruct.2019.03.090
Aly, N., Galal, K. (2020a). Effect of Ductile Shear Wall Ratio and Cross-Section Configuration on Seismic Behavior of Reinforced Concrete Masonry Shear Wall Buildings. Journal of Structural Engineering (United States), 146(4), 1–15. https://doi.org/10.1061/(ASCE)ST.1943-541X.0002542
Aly, N., Galal, K. (2020b). Experimental Investigation of Axial Load and Detailing Effects on the Inelastic Response of Reinforced-Concrete Masonry Structural Walls with Boundary Elements. Journal of Structural Engineering, 146(12), 04020259. https://doi.org/10.1061/(asce)st.1943-541x.0002842
Aly, N., Galal, K. (2020c). In-Plane Cyclic Response of High-Rise Reinforced Concrete Masonry Structural Walls with Boundary Elements. Engineering Structures, 219(August 2019), 110771. https://doi.org/10.1016/j.engstruct.2020.110771
Arnau, O., Sandoval, C., Murià-Vila, D. (2015). Determination and validation of input parameters for detailed micro-modelling of partially grouted reinforced masonry walls. Proceedings of the Tenth Pacific Conference on Earthquake Engineering Building an Earthquake-Resilient Pacific, (November). Retrieved from https://www.researchgate.net/publication/289988824
ASCE/SEI. (2017). ASCE Standard, ASCE/SEI, 41-17, Seismic Evaluation and Retrofit of Existing Buildings. ASCE/SEI 41-17. Reston, VA: American Society of Civil Engineers. https://doi.org/10.1061/9780784414859
Ashour, A., El-Dakhakhni, W. (2016a). Backbone Model for Displacement-Based Seismic Design of Reinforced Masonry Shear Wall Buildings. Brick and Block Masonry: Trends, Innovations and Challenges - Proceedings of the 16th International Brick and Block Masonry Conference, IBMAC 2016, 65–70. https://doi.org/10.1201/b21889-6
Ashour, A., El-Dakhakhni, W. (2016b). Influence of Floor Diaphragm–Wall Coupling on the System-Level Seismic Performance of an Asymmetrical Reinforced Concrete Block Building. Journal of Structural Engineering, 142(10), 04016071. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001540
Ashour, A., El-Dakhakhni, W., Shedid, M. (2016). Experimental Evaluation of the System-Level Seismic Performance and Robustness of an Asymmetrical Reinforced Concrete Block Building. Journal of Structural Engineering, 142(10), 04016072. https://doi.org/10.1061/(asce)st.1943-541x.0001529
Ashour, A., Galal, K. (2017). Load-Displacement Backbone Model for Flexure-Dominated Reinforced Masonry Shear Walls. In 13TH CANADIAN MASONRY SYMPOSIUM. Halifax, Canada.
ASTM. (2009). C 509: Standard specification for cellular elastomeric preformed gasket and sealing material.
ASTM. (2012). C 952-12. Standard test method for bond strength of mortar to masonry units. In American Society for Testing and Materials.
ASTM. (2015). Standard Test Methods for In Situ Measurement Of Masonry Mortar Joint Shear. ASTM (Vol. 04).
ASTM. (2016). C109/109M-16a Standard test method for compressive strength of hydraulic cement mortars (Using 2-in. or cube specimens). Annual Book of ASTM Standards, 04, 1–10. https://doi.org/10.1520/C0109
ASTM. (2018a). ASTM C1314 - Standard Test Method for Compressive Strength of Masonry Prisms. ASTM International, 1–10. https://doi.org/10.1520/C1314-18.2
ASTM. (2018b). C39 / C39M-18, Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens. ASTM International, West Conshohocken, PA.
ASTM. (2020a). A615/A615M − 20 Standard Specification for Deformed and Plain Billet-Steel Bars for Concrete. ASTM International, West Conshohocken, PA 19428-2959. United States. https://doi.org/10.1520/A0615
ASTM. (2020b). C140/C140M − 20a Standard test methods for Sampling and Testing Concrete Masonry Units and Related Units. ASTM International, West Conshohocken, PA 19428–2959. United States. https://doi.org/10.1520/C0140_C0140M-20A
ASTM. (2022). A1064/A1064M − 22 Standard Specification for Carbon-Steel Wire and Welded Wire Reinforcement, Plain and Deformed, for Concrete (Vol. i). ASTM A1064M. West Conshohocken, PA: ASTM. https://doi.org/10.1520/A1064_A1064M-22
Astroza, M., Moroni, O., Brzev, S., Tanner, J. (2012). Seismic Performance of Engineered Masonry Buildings in the 2010 Maule Earthquake. Earthquake Spectra, 28(SUPPL.1), 385–406. https://doi.org/10.1193/1.4000040
ATC. (2010). PEER/ATC 72-1: Modeling and Acceptance Criteria for Seismic Design and Analysis of Tall Buildings. Applied Technology Council. Retrieved from http://peer.berkeley.edu/peer_ground_motion_database
Banting, B. R., El-Dakhakhni, W. W. (2012). Force- and Displacement-Based Seismic Performance Parameters for Reinforced Masonry Structural Walls with Boundary Elements. Journal of Structural Engineering, 138(12), 1477–1491. https://doi.org/10.1061/(asce)st.1943-541x.0000572
Banting, B. R., El-Dakhakhni, W. W. (2014). Seismic Performance Quantification of Reinforced Masonry Structural Walls with Boundary Elements. Journal of Structural Engineering, 140(5), 04014001. https://doi.org/10.1061/(asce)st.1943-541x.0000895
Berto, L., Saetta, A., Scotta, R., Vitaliani, R. (2004). Shear Behaviour of Masonry Panel: Parametric FE Analyses. International Journal of Solids and Structures, 41(16–17), 4383–4405. https://doi.org/10.1016/j.ijsolstr.2004.02.046
Bolhassani, M. (2015). Improvement of Seismic Performance of Ordinary Reinforced Partially Grouted Concrete Masonry Shear Walls. Ph.D Thesis, Drexel University.
Bolhassani, M., Hamid, A. A., Johnson, C., Moon, F. L., Schultz, A. E. (2016a). New Design Detail to Enhance the Seismic Performance of Ordinary Reinforced Partially Grouted Masonry Structures. Journal of Structural Engineering (United States), 142(12), 1–15. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001620
Bolhassani, M., Hamid, A. A., Moon, F. L. (2016b). Enhancement of Lateral In-Plane Capacity of Partially Grouted Concrete Masonry Shear Walls. Engineering Structures, 108, 59–76. https://doi.org/10.1016/j.engstruct.2015.11.017
Bolhassani, M., Hamid, A., Lau, A., Moon, F. (2015). Simplified Micro Modeling of Partially Grouted Masonry Assemblages. Construction and Building Materials, 83, 159–173. https://doi.org/10.1016/j.conbuildmat.2015.03.021
British Standard. (2002). BS EN 1052-3 Methods of test for masonry-Part 3: Determination of initial shear strength. British standard (Vol. 3).
Calderón, S., Arnau, O., Sandoval, C. (2019). Detailed Micro-Modeling Approach and Solution Strategy for Laterally Loaded Reinforced Masonry Shear Walls. Engineering Structures, 201(February), 109786. https://doi.org/10.1016/j.engstruct.2019.109786
Calderón, S., Milani, G., Sandoval, C. (2021a). Simplified micro-modeling of partially-grouted reinforced masonry shear walls with bed-joint reinforcement: Implementation and validation. Engineering Structures, 234(January). https://doi.org/10.1016/j.engstruct.2021.111987
Calderón, S., Sandoval, C., Arnau, O. (2017a). Shear Response of Partially-Grouted Reinforced Masonry Walls with a Central Opening: Testing and Detailed Micro-Modelling. Materials and Design, 118, 122–137. https://doi.org/10.1016/j.matdes.2017.01.019
Calderón, S., Sandoval, C., Arnau, O. (2017b). Shear Response of Partially-Grouted Reinforced Masonry Walls with A Central Opening: Testing and Detailed Micro-Modelling. Materials and Design, 118, 122–137. https://doi.org/10.1016/j.matdes.2017.01.019
Calderón, S., Sandoval, C., Milani, G., Arnau, O. (2021b). Detailed micro-modeling of partially grouted reinforced masonry shear walls: extended validation and parametric study. Archives of Civil and Mechanical Engineering, 21(3), 1–24. https://doi.org/10.1007/s43452-021-00237-z
Calvi, G. M., Priestley, M. J. N., Kowalsky, M. J. (2008). Displacement-Based Seismic Design of Structures. Earthquake Spectra, 24(2), 555–557. https://doi.org/10.1193/1.2932170
CEN. (2007). European Norm for Methods of Test for Masonry – Part 3: Determination of Initial Shear Strength.
Chaimoon, K., Attard, M. M. (2009). Experimental and numerical investigation of masonry under three-point bending (in-plane). Engineering Structures, 31(1), 103–112. https://doi.org/10.1016/j.engstruct.2008.07.018
Chen, S.-W. J., Hidalgo, P. A., Mayes, R. L., Clough, R. W., Mcniven, H. D. (1978a). Cyclic Loading Tests of Masonry Single Piers Volume 2- Height to Width Ratio Of 1.
Chen, S.-W. J., Hidalgo, P. A., Mayes, R. L., Mcniven, H. D., Clough, R. W. (1978b). Cyclic Loading Tests of Masonry Single Piers, Volume 2 - Height to Width Ratio of 2.
Chopra, A. K. (2007). Dynamics of structures: Theory and applications to earthquake engineering. 3rd ed. Upper Saddle River, NJ: Pearson Prentice Hall.
Citto, C., Wo, S. I., Willam, K. J., Schuller, M. P. (2011). In-Place Evaluation of Masonry Shear Behavior Using Digital Image Analysis. ACI Materials Journal, 108(4). https://doi.org/10.14359/51683114
Correa, M. R. S. (2016). A 20-storey high masonry building in Brazil—Design problems and adopted strategies. In Proc., 16th Int. Brick and Block Masonry Conf (pp. 623–628).
CSA. (2014a). Canadian Standards Association (CSA) S304-14, Design of Masonry Structures. CSA Group. Mississauga, Ontario, Canada.
CSA. (2014b). Canadian Standards Association A165.1 CSA Standards on concrete masonry units. CSA Group, Mississauga, Ontario, Canada. Retrieved from https://www.researchgate.net/publication/269107473_What_is_governance/link/548173090cf22525dcb61443/download%0Ahttp://www.econ.upf.edu/~reynal/Civil wars_12December2010.pdf%0Ahttps://think-asia.org/handle/11540/8282%0Ahttps://www.jstor.org/stable/41857625
CSA. (2014c). Canadian Standards Association CSA-A179-14 Mortar and grout for unit masonry (Vol. 14).
CSA. (2024). Canadian Standards Association (CSA) S304-24, Design of Masonry Structures. Mississauga, Ontario, Canada: CSA Group.
D’Altri, A. M., de Miranda, S., Castellazzi, G., Sarhosis, V. (2018). A 3D Detailed Micro-Model for the In-Plane and Out-Of-Plane Numerical Analysis of Masonry Panels. Computers and Structures, 206, 18–30. https://doi.org/10.1016/j.compstruc.2018.06.007
Drysdale, R. G., Hamid, A. A. (2005). Masonry Structures Behaviour and Design. Canada Masonry Design Centre, Mississauga, Ontario.
Elmapruk, J., ElGawady, M. A., Hassanli, R. (2020). Experimental and Analytical Study on the Shear-Strength of Partially Grouted Masonry Walls. Journal of Structural Engineering, 146(8), 04020147. https://doi.org/10.1061/(asce)st.1943-541x.0002704
Elmapruk, J. H. (2010). Shear Strength of Partially Grouted. WASHINGTON STATE UNIVERSITY.
Elmeligy, O., AbdelRahman, B., Galal, K. (2024a). Experimental investigation of the compressive and shear behaviours of grouted and hollow masonry constructed with PVA fibre-reinforced mortar and grout. Construction and Building Materials, 415(January), 134954. https://doi.org/10.1016/j.conbuildmat.2024.134954
Elmeligy, O., AbdelRahman, B., Galal, K. (2024b). Numerical assessment of TMS 402/602-22 and CSA S304-14 seismic design provisions for partially grouted reinforced masonry shear walls failing in flexure. Engineering Structures, 303(December 2023), 117370. https://doi.org/10.1016/j.engstruct.2023.117370
Elmeligy, O., Aly, N., Galal, K. (2021). Sensitivity analysis of the numerical simulations of partially grouted reinforced masonry shear walls. Engineering Structures, 245(March), 112876. https://doi.org/10.1016/j.engstruct.2021.112876
Elmeligy, O. M. M. (2023). In-plane Cyclic Response of Slender Rectangular and Flanged Partially Grouted Reinforced Masonry Shear Walls Failing in Flexure. Concordia University, Montreal, Canada.
Ewing, R. D., El-Mustapha, A. M., Karlotis, J. C. (1990). Fem/I A Finite Element Computer Program for the Nonlinear Static Analysis of Reinforced Masonry Building Components. U.S. - Japan Coordinated Program for Masonry Building Research (Vol. 53). https://doi.org/10.1017/CBO9781107415324.004
Ezzeldin, M., El-Dakhakhni, W., Wiebe, L. (2018). Reinforced Masonry Building Seismic Response Models for ASCE/SEI-41. Journal of Structural Engineering, 144(1), 04017175. https://doi.org/10.1061/(asce)st.1943-541x.0001914
Ezzeldin, M., Wiebe, L., El-Dakhakhni, W. (2016). Seismic Collapse Risk Assessment of Reinforced Masonry Walls with Boundary Elements Using the FEMA P695 Methodology. Journal of Structural Engineering, 142(11). https://doi.org/10.1061/(asce)st.1943-541x.0001579
Fava, M., Munari, M., da Porto, F., Modena, C. (2016). Seismic vulnerability assessment of existing masonry buildings by nonlinear static analyses and fragility curves. Brick and Block Masonry: Trends, Innovations and Challenges - Proceedings of the 16th International Brick and Block Masonry Conference, IBMAC 2016, 2409–2416. https://doi.org/10.1201/b21889-315
Gilbert, R., Warner, R. (1978). Tension Stiffening in Reinforced Concrete Slabs. Journal of the Structural Division, 104(12), 1885–1900.
Gouda, O., Hassanein, A., Youssef, T., Galal, K. (2021). Stress-Strain Behaviour of Masonry Prisms Constructed with Glass Fibre-Reinforced Grout. Construction and Building Materials, 267, 120984. https://doi.org/10.1016/j.conbuildmat.2020.120984
Halucha, J. A. (2002). In-Plane Shear Behaviour of Reinforced Concrete Masonry Panels Under Biaxial Loading. M.A.Sc. Thesis, McMaster University. Hamilton, Ontario.
Hamedzadeh, A. (2013). On The Shear Strength Of Partially Grouted Concrete Masonry. CALGARY, ALBERTA. https://doi.org/10.11575/PRISM/27195
Hamid, A. A., Gouda, M. G. (1991). Partially Reinforced Concrete Masonry. Brick and Block Masonry, 1, 368–378.
Hansen, K. F., Nykanen, E., Gottfredsen, F. R. (1998). Shear behaviour of bed joints at different levels of precompression. Masonry International, 12(2), 70–78.
Hashemi, A., Mosalam, K. M. (2006). Shake-table experiment on reinforced concrete structure containing masonry infill wall. Earthquake Engineering & Structural Dynamics, 35(14), 1827–1852. https://doi.org/10.1002/eqe.612
Hendry, A. W. (1998). Structural Masonry. London: Macmillan Education UK. https://doi.org/10.1007/978-1-349-14827-1
Hidalgo, P. A., Mayes, R. L., Mcniven, H. D., Clough, R. (1978). Cyclic Loading Tests of Masonry Single Piers, Volume 1. Height to Width Ratio Of 2.
Hoque, N. (2013). In-Plane Cyclic Testing of Reinforced Concrete Masonry Walls to Assess the Effect of Varying Reinforcement Anchorage and Boundary Conditions. CALGARY, ALBERTA. https://doi.org/10.11575/PRISM/26545
Hsu, L. S., Hsu, C.-T. T. (1994). Complete Stress-Strain Behaviour of High-Strength Concrete Under Compression. Magazine of Concrete Research, 46(169), 301–312. https://doi.org/10.1680/macr.1994.46.169.301
Inc., T. M. (2022). MATLAB version: 9.13.0 (R2022b). Natick, Massachusetts, United States: The MathWorks Inc. Retrieved from https://www.mathworks.com
Johnson, C. A., Schultz, A. E. (2014). Simulated Seismic Testing of Partially-Grouted Masonry Subassemblages. NCEE 2014 - 10th U.S. National Conference on Earthquake Engineering: Frontiers of Earthquake Engineering. https://doi.org/10.4231/D3HX15R69
Khalaf, F. M. (2005). New Test for Determination of Masonry Tensile Bond Strength. Journal of Materials in Civil Engineering, 17(6), 725–732. https://doi.org/10.1061/(ASCE)0899-1561(2005)17:6(725)
Khan, M., Cao, M., Ali, M. (2018). Effect of basalt fibers on mechanical properties of calcium carbonate whisker-steel fiber reinforced concrete. Construction and Building Materials, 192, 742–753. https://doi.org/10.1016/j.conbuildmat.2018.10.159
Lin, C.-S., Scordelis, A. C. (1975). Nonlinear Analysis of RC Shells of General Form. Journal of the Structural Division, 101(3), 523–538.
Lizárraga, J. F., Pérez-Gavilán, J. J. (2017). Parameter estimation for nonlinear analysis of multi-perforated concrete masonry walls. Construction and Building Materials, 141, 353–365. https://doi.org/10.1016/j.conbuildmat.2017.03.008
Lourenço, P. (1996). Computational Strategy for Masonry Structures.
Lourenço, P. B., Barros, J. O., Oliveira, J. T. (2004). Shear testing of stack bonded masonry. Construction and Building Materials, 18(2), 125–132. https://doi.org/10.1016/j.conbuildmat.2003.08.018
Lourenço, P. B., Ramos, L. F. (2004). Characterization of Cyclic Behavior of Dry Masonry Joints. Journal of Structural Engineering, 130(5), 779–786. https://doi.org/10.1061/(ASCE)0733-9445(2004)130:5(779)
Lourenço, P. B., Rots, J. G. (1997). Multisurface Interface Model for Analysis of Masonry Structures. Journal of Engineering Mechanics, 123(7), 660–668. https://doi.org/10.1061/(ASCE)0733-9399(1997)123:7(660)
Magenes, G., Calvi, G. M. (1997). In-plane seismic response of brick masonry walls. Earthquake Engineering & Structural Dynamics, 26(11), 1091–1112. https://doi.org/10.1002/(SICI)1096-9845(199711)26:11<1091::AID-EQE693>3.0.CO;2-6
Mahrous, A., AbdelRahman, B., Galal, K. (2022). Seismic response analysis of reinforced masonry core walls with boundary elements. Engineering Structures, 270(September), 114882. https://doi.org/10.1016/j.engstruct.2022.114882
Maleki, M. (2008). Behaviour of Partially Grouted Reinforced Masonry Shear Walls Under Cyclic Reversed Loading. McMaster University.
Medeiros, K. A. S., Chavez, K. H., Fonseca, F. S., Parsekian, G. A., Shrive, N. G. (2021). Parametric study of multi-story, perforated, partially grouted masonry walls subjected to in-plane cyclic actions. Canadian Journal of Civil Engineering, 48(8), 1046–1055. https://doi.org/10.1139/cjce-2020-0128
Meli, R. (1973). Behaviour of masonry walls under lateral loads. In The 5th World Congress on Earthquake Engineering (pp. 853–862).
Milani, G. (2008). 3D Upper Bound Limit Analysis of Multi-Leaf Masonry Walls. International Journal of Mechanical Sciences, 50(4), 817–836. https://doi.org/10.1016/j.ijmecsci.2007.11.003
Milani, G. (2010). 3D FE Limit Analysis Model for Multi-Layer Masonry Structures Reinforced with FRP Strips. International Journal of Mechanical Sciences, 52(6), 784–803. https://doi.org/10.1016/j.ijmecsci.2010.01.004
Milani, G. (2011a). Simple Homogenization Model for the Non-Linear Analysis of In-Plane Loaded Masonry Walls. Computers and Structures, 89(17–18), 1586–1601. https://doi.org/10.1016/j.compstruc.2011.05.004
Milani, G. (2011b). Simple Lower Bound Limit Analysis Homogenization Model for In- And Out-Of-Plane Loaded Masonry Walls. Construction and Building Materials, 25(12), 4426–4443. https://doi.org/10.1016/j.conbuildmat.2011.01.012
Minaie, E. (2009). Behavior and Vulnerability of Reinforced Masonry Shear Walls. Ph.D Thesis, Drexel University.
Minaie, E., Moon, F. L., Hamid, A. A. (2014). Nonlinear Finite Element Modeling of Reinforced Masonry Shear Walls for Bidirectional Loading Response. Finite Elements in Analysis and Design, 84, 44–53. https://doi.org/10.1016/j.finel.2014.02.001
Minaie, E., Mota, M., Moon, F. L., Hamid, A. A. (2010). In-Plane Behavior of Partially Grouted Reinforced Concrete Masonry Shear Walls. Journal of Structural Engineering, 136(9), 1089–1097. https://doi.org/10.1061/(asce)st.1943-541x.0000206
NAHB Research Center. (1998). Building Concrete Masonry Homes :Design and Construction Issues. Upper Marlboro, MD, USA.
Nasiri, E., Liu, Y. (2017). Development of a detailed 3D FE model for analysis of the in-plane behaviour of masonry infilled concrete frames. Engineering Structures, 143, 603–616. https://doi.org/10.1016/j.engstruct.2017.04.049
Nayal, R., Rasheed, H. A. (2006). Tension Stiffening Model for Concrete Beams Reinforced with Steel and FRP Bars. Journal of Materials in Civil Engineering, 18(6), 831–841. https://doi.org/10.1061/(ASCE)0899-1561(2006)18:6(831)
Nolph, H. M. (2010). In-Plane Shear Performance of Partially Grouted Masonry Shear Walls. Master. Thesis, Department of Civil and Environmental Engineering, WASHINGTON STATE UNIVERSITY.
Nolph, S. M., ElGawady, M. A. (2012). Static Cyclic Response of Partially Grouted Masonry Shear Walls. Journal of Structural Engineering, 138(7), 864–879. https://doi.org/10.1061/(asce)st.1943-541x.0000529
Paulay, T. (1997). Seismic Torsional Effects on Ductile Structural Wall Systems. Journal of Earthquake Engineering, 1(4), 721–745. https://doi.org/10.1080/13632469708962385
Paulay, T., Priestly, M. J. N. (1992). Seismic Design of Reinforced Concrete and Masonry Buildings. Hoboken, NJ, USA: John Wiley & Sons, Inc. https://doi.org/10.1002/9780470172841
Priestley, M. J. N., Calvi, G. M., Kowalsky, M. J. (2007a). Displacement based seismic design of stuctures. IUSS Press, Pavia, Italy.
Priestley, M. J. N., Elder, D. M. G. (1982). Cyclic Loading Tests of Slender Concrete Masonry Shear Walls. Bulletin of the New Zealand National Society for Earthquake Engineering, 15(1), 3–21. https://doi.org/10.5459/bnzsee.15.1.3-21
Priestley, M. J. N., G.M. Calvi, M.J.Kowalsky. (2007b). Direct Displacement-Based Seismic Design of Structures. In NZSEE Conference (Vol. 24, pp. 555–557). https://doi.org/10.1193/1.2932170
Priestley, N., Calvi, G., Kowalsky, M. (2007c). Displacement-Based Seismic Design of Structures. IUSS Press, Pavia, Italy.
Redmond, L., Stavridis, A., DesRoches, R. (2014). Development of a Finite Element Model for Partially Grouted Masonry. NCEE 2014 - 10th U.S. National Conference on Earthquake Engineering: Frontiers of Earthquake Engineering, (September 2015). https://doi.org/10.4231/D3PN8XG1V
Rizaee. (2015). Assessing Bond Beam Horizontal Reinforcement Efficacy with Different End Anchorage Conditions in Concrete Block Masonry Shear Walls. Acta Universitatis Agriculturae et Silviculturae Mendelianae Brunensis. CALGARY, ALBERTA. https://doi.org/10.11575/PRISM/25017
Sandoval, C., Arnau, O. (2017). Experimental characterization and detailed micro-modeling of multi-perforated clay brick masonry structural response. Materials and Structures/Materiaux et Constructions, 50(1). https://doi.org/10.1617/s11527-016-0888-3
Sarhosis, V., Lemos, J. V. (2018). A Detailed Micro-Modelling Approach for the Structural Analysis of Masonry Assemblages. Computers and Structures, 206, 66–81. https://doi.org/10.1016/j.compstruc.2018.06.003
Scanlon, A., Murray, D. W. (1974). Time Dependent Deflections of Reinforced Concrete Slab Deflections. Journal of the Structural Division, 100(9), 1911– 1924.
Schultz, A. E. (1994). NIST Research Program on the Seismic Resistance of Partially-Grouted Masonry Shear Walls. National Institute of Standards and Technology.
Schultz, A. E., Johnson, C. A. (2019). Seismic Resistance Mechanisms in Partially Grouted Shear Walls with New Design Details. In 13th North American Masonry Conf. The Masonry Society. Salt Lake City, UT, USA.
Shedid, M. T. (2009). Strategies To Enhance Seismic Performance of Reinforced Masonry Shear Walls. (Canada): McMaster University; 2009. Ph.D. thesis.
Shedid, M. T., El-Dakhakhni, W. W., Drysdale, R. G. (2009). Behavior of fully grouted reinforced concrete masonry shear walls failing in flexure: Analysis. Engineering Structures, 31(9), 2032–2044. https://doi.org/10.1016/j.engstruct.2009.03.006
Shedid, M. T., El-Dakhakhni, W. W., Drysdale, R. G. (2010a). Alternative Strategies to Enhance the Seismic Performance of Reinforced Concrete-Block Shear Wall Systems. Journal of Structural Engineering, 136(6), 676–689. https://doi.org/10.1061/(asce)st.1943-541x.0000164
Shedid, M. T., El-Dakhakhni, W. W., Drysdale, R. G. (2010b). Characteristics of Rectangular, Flanged, and End-Confined Reinforced Concrete Masonry Shear Walls for Seismic Design. Journal of Structural Engineering, 136(12), 1471–1482. https://doi.org/10.1061/(asce)st.1943-541x.0000253
Shing, P. B., Lotfi, H. R., Barzegarmehrabi, A., Brunner, J. (1992). Finite Element Analysis of Shear Resistance of Masonry Wall Panels with and without Confining Frames. Earthquake Engineering, Tenth World Conference.
Siyam, M. A., El-Dakhakhni, W. W., Shedid, M. T., Drysdale, R. G. (2016). Seismic Response Evaluation of Ductile Reinforced Concrete Block Structural Walls. I: Experimental Results and Force-Based Design Parameters. Journal of Performance of Constructed Facilities, 30(4), 1–14. https://doi.org/10.1061/(ASCE)CF.1943-5509.0000794
Stavridis, A., Shing, P. B. (2010). Finite-element modeling of nonlinear behavior of masonry-infilled RC frames. Journal of Structural Engineering, 136(3), 285–296. https://doi.org/10.1061/(ASCE)ST.1943-541X.116
Tagel-Din, H., Meguro, K. (2000). APPLIED ELEMENT METHOD FOR DYNAMIC LARGE DEFORMATION ANALYSIS OF STRUCTURES. Doboku Gakkai Ronbunshu, 2000(661), 1–10. https://doi.org/10.2208/jscej.2000.661_1
Taylor-Firth, A., Taylor, I. F. (1990). A bond tensile strength test for use in assessing the compatibility of Brick/Mortar interfaces. Construction and Building Materials, 4(2), 58–63. https://doi.org/10.1016/0950-0618(90)90001-H
Thurston, S. J., Hutchison, D. L. (1982). Reinforced Masonry Shear Walls: Cyclic Load Tests in Contraflexure. Bulletin of the New Zealand National Society for Earthquake Engineering, 15(1), 27–45.
Tomazevic, M. (1999). Earthquake-Resistant Design of Masonry Buildings (Vol. 1). PUBLISHED BY IMPERIAL COLLEGE PRESS AND DISTRIBUTED BY WORLD SCIENTIFIC PUBLISHING CO. https://doi.org/10.1142/p055
Tomaževič, M. (1999). Earthquake-resistant design of masonry buildings. TA - TT -. London, Singapore SE - xii, 268 pages : illustrations ; 23 cm.: Imperial College Press ; Distributed by World Scientific London, Singapore. https://doi.org/LK - https://worldcat.org/title/40776879
Usman, M., Farooq, S. H., Umair, M., Hanif, A. (2020). Axial compressive behavior of confined steel fiber reinforced high strength concrete. Construction and Building Materials, 230, 117043. https://doi.org/10.1016/j.conbuildmat.2019.117043
Valdebenito, G., Alvarado, D., Sandoval, C., Aguilar, V. (2015). Terremoto De Iquique Mw=8,2 - 01 Abril 2014: Daños Observados Y Efectos De Sitio En Estructuras De Albañilería. In XI Congr. Chil. Sismol. e Ing. Sísmica 922 ACHISINA. 18-20 March, Santiago. Chile.
Van Der Pluijm, R. (1997). Non-linear behaviour of masonry under tension. Heron, 42(1), 25–48.
Van der Pluijm, R., Rutten, H. S., Ceelen, M. (2000). Shear behaviour of bed joints. In conference; 12th International Brick/Block Masonry Conference; 2000-06-25; 2000-06-28 (p. 12).
Van derPluijm, R. (1999). Out-of-Plane Bending of Masonry Behaviour and Strength. (Phd Thesis) Technische Universiteit Eindhoven. https://doi.org/10.6100/IR528212
Vebo, A., Ghali, A. (1977). Moment-Curvature Relation of Reinforced Concrete Slabs. Journal of the Structural Division, 103(3), 515–531.
Voon, K. C., Ingham, J. M. (2003). SHEAR STRENGTH OF CONCRETE MASONRY WALLS.
Zhang, Z., Murcia-Delso, J., Sandoval, C., Araya-Letelier, G., Wang, F. (2021). In-plane shear strength and damage fragility functions for partially-grouted reinforced masonry walls with bond-beam reinforcement. Engineering Structures, 242. https://doi.org/10.1016/j.engstruct.2021.112569
ABAQUS. (2013). 6.13-3. RI Abaqus analysis user’s manual. USA: Dassault Systems Providence.
AbdAllah, A. R., AbdelRahman, B., Galal, K. (2023). Numerical study of the seismic performance of fully grouted reinforced masonry shear walls with boundary elements subjected to dynamic loading. Engineering Structures, 295(July), 116804. https://doi.org/10.1016/j.engstruct.2023.116804
AbdelRahman, B., Galal, K. (2020). Influence of pre-wetting, non-shrink grout, and scaling on the compressive strength of grouted concrete masonry prisms. Construction and Building Materials, 241, 117985. https://doi.org/10.1016/j.conbuildmat.2019.117985
Ahmad, S. H., Xie, Y., Yu, T. (1995). Shear ductility of reinforced lightweight concrete beams of normal strength and high strength concrete. Cement and Concrete Composites, 17(2), 147–159. https://doi.org/10.1016/0958-9465(94)00029-X
Albutainy, M., Galal, K. (2021). Experimental investigation of reinforced concrete masonry shear walls with C-shaped masonry units boundary elements. Structures, 34(October), 3667–3683. https://doi.org/10.1016/j.istruc.2021.09.080
Albutainy, M., Galal, K. (2024). Effect of boundary element detailing on the seismic performance of reinforced concrete masonry shear walls. Engineering Structures, 300(January 2023), 117164. https://doi.org/10.1016/j.engstruct.2023.117164
Albutainy, M. L. (2016). Seismic Performance of Ductile Reinforced Concrete Masonry Shear Walls with C-Shaped Boundary Elements. Ph.D. Thesis, Building, Civil, and Environmental Engineering, Concordia University, Montreal, Quebec, Canada. Retrieved from https://medium.com/@arifwicaksanaa/pengertian-use-case-a7e576e1b6bf
Alecci, V., Fagone, M., Rotunno, T., De Stefano, M. (2013). Shear strength of brick masonry walls assembled with different types of mortar. Construction and Building Materials, 40, 1038–1045. https://doi.org/10.1016/j.conbuildmat.2012.11.107
Almeida, J. C., Lourenço, P. B., Barros, J. (2002). Characterization of masonry under uniaxial tension. In VII International Seminar on Structural Masonry for Developing Contries (p. 24). Belo Horizonte, Brazil. Retrieved from http://www.civil.uminho.pt/masonry/Publications/2002_Lourenco_et_al.pdf
Aly, N. E. (2019). Seismic performance and height limits of ductile reinforced masonry shear wall buildings with boundary elements. Ph.D. Thesis, Building, Civil, and Environmental Engineering, Concordia University, Montreal, Quebec, Canada. https://doi.org/10.1016/j.engstruct.2019.03.090
Aly, N., Galal, K. (2020a). Effect of Ductile Shear Wall Ratio and Cross-Section Configuration on Seismic Behavior of Reinforced Concrete Masonry Shear Wall Buildings. Journal of Structural Engineering (United States), 146(4), 1–15. https://doi.org/10.1061/(ASCE)ST.1943-541X.0002542
Aly, N., Galal, K. (2020b). Experimental Investigation of Axial Load and Detailing Effects on the Inelastic Response of Reinforced-Concrete Masonry Structural Walls with Boundary Elements. Journal of Structural Engineering, 146(12), 04020259. https://doi.org/10.1061/(asce)st.1943-541x.0002842
Aly, N., Galal, K. (2020c). In-Plane Cyclic Response of High-Rise Reinforced Concrete Masonry Structural Walls with Boundary Elements. Engineering Structures, 219(August 2019), 110771. https://doi.org/10.1016/j.engstruct.2020.110771
Arnau, O., Sandoval, C., Murià-Vila, D. (2015). Determination and validation of input parameters for detailed micro-modelling of partially grouted reinforced masonry walls. Proceedings of the Tenth Pacific Conference on Earthquake Engineering Building an Earthquake-Resilient Pacific, (November). Retrieved from https://www.researchgate.net/publication/289988824
ASCE/SEI. (2017). ASCE Standard, ASCE/SEI, 41-17, Seismic Evaluation and Retrofit of Existing Buildings. ASCE/SEI 41-17. Reston, VA: American Society of Civil Engineers. https://doi.org/10.1061/9780784414859
Ashour, A., El-Dakhakhni, W. (2016a). Backbone Model for Displacement-Based Seismic Design of Reinforced Masonry Shear Wall Buildings. Brick and Block Masonry: Trends, Innovations and Challenges - Proceedings of the 16th International Brick and Block Masonry Conference, IBMAC 2016, 65–70. https://doi.org/10.1201/b21889-6
Ashour, A., El-Dakhakhni, W. (2016b). Influence of Floor Diaphragm–Wall Coupling on the System-Level Seismic Performance of an Asymmetrical Reinforced Concrete Block Building. Journal of Structural Engineering, 142(10), 04016071. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001540
Ashour, A., El-Dakhakhni, W., Shedid, M. (2016). Experimental Evaluation of the System-Level Seismic Performance and Robustness of an Asymmetrical Reinforced Concrete Block Building. Journal of Structural Engineering, 142(10), 04016072. https://doi.org/10.1061/(asce)st.1943-541x.0001529
Ashour, A., Galal, K. (2017). Load-Displacement Backbone Model for Flexure-Dominated Reinforced Masonry Shear Walls. In 13TH CANADIAN MASONRY SYMPOSIUM. Halifax, Canada.
ASTM. (2009). C 509: Standard specification for cellular elastomeric preformed gasket and sealing material.
ASTM. (2012). C 952-12. Standard test method for bond strength of mortar to masonry units. In American Society for Testing and Materials.
ASTM. (2015). Standard Test Methods for In Situ Measurement Of Masonry Mortar Joint Shear. ASTM (Vol. 04).
ASTM. (2016). C109/109M-16a Standard test method for compressive strength of hydraulic cement mortars (Using 2-in. or cube specimens). Annual Book of ASTM Standards, 04, 1–10. https://doi.org/10.1520/C0109
ASTM. (2018a). ASTM C1314 - Standard Test Method for Compressive Strength of Masonry Prisms. ASTM International, 1–10. https://doi.org/10.1520/C1314-18.2
ASTM. (2018b). C39 / C39M-18, Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens. ASTM International, West Conshohocken, PA.
ASTM. (2020a). A615/A615M − 20 Standard Specification for Deformed and Plain Billet-Steel Bars for Concrete. ASTM International, West Conshohocken, PA 19428-2959. United States. https://doi.org/10.1520/A0615
ASTM. (2020b). C140/C140M − 20a Standard test methods for Sampling and Testing Concrete Masonry Units and Related Units. ASTM International, West Conshohocken, PA 19428–2959. United States. https://doi.org/10.1520/C0140_C0140M-20A
ASTM. (2022). A1064/A1064M − 22 Standard Specification for Carbon-Steel Wire and Welded Wire Reinforcement, Plain and Deformed, for Concrete (Vol. i). ASTM A1064M. West Conshohocken, PA: ASTM. https://doi.org/10.1520/A1064_A1064M-22
Astroza, M., Moroni, O., Brzev, S., Tanner, J. (2012). Seismic Performance of Engineered Masonry Buildings in the 2010 Maule Earthquake. Earthquake Spectra, 28(SUPPL.1), 385–406. https://doi.org/10.1193/1.4000040
ATC. (2010). PEER/ATC 72-1: Modeling and Acceptance Criteria for Seismic Design and Analysis of Tall Buildings. Applied Technology Council. Retrieved from http://peer.berkeley.edu/peer_ground_motion_database
Banting, B. R., El-Dakhakhni, W. W. (2012). Force- and Displacement-Based Seismic Performance Parameters for Reinforced Masonry Structural Walls with Boundary Elements. Journal of Structural Engineering, 138(12), 1477–1491. https://doi.org/10.1061/(asce)st.1943-541x.0000572
Banting, B. R., El-Dakhakhni, W. W. (2014). Seismic Performance Quantification of Reinforced Masonry Structural Walls with Boundary Elements. Journal of Structural Engineering, 140(5), 04014001. https://doi.org/10.1061/(asce)st.1943-541x.0000895
Berto, L., Saetta, A., Scotta, R., Vitaliani, R. (2004). Shear Behaviour of Masonry Panel: Parametric FE Analyses. International Journal of Solids and Structures, 41(16–17), 4383–4405. https://doi.org/10.1016/j.ijsolstr.2004.02.046
Bolhassani, M. (2015). Improvement of Seismic Performance of Ordinary Reinforced Partially Grouted Concrete Masonry Shear Walls. Ph.D Thesis, Drexel University.
Bolhassani, M., Hamid, A. A., Johnson, C., Moon, F. L., Schultz, A. E. (2016a). New Design Detail to Enhance the Seismic Performance of Ordinary Reinforced Partially Grouted Masonry Structures. Journal of Structural Engineering (United States), 142(12), 1–15. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001620
Bolhassani, M., Hamid, A. A., Moon, F. L. (2016b). Enhancement of Lateral In-Plane Capacity of Partially Grouted Concrete Masonry Shear Walls. Engineering Structures, 108, 59–76. https://doi.org/10.1016/j.engstruct.2015.11.017
Bolhassani, M., Hamid, A., Lau, A., Moon, F. (2015). Simplified Micro Modeling of Partially Grouted Masonry Assemblages. Construction and Building Materials, 83, 159–173. https://doi.org/10.1016/j.conbuildmat.2015.03.021
British Standard. (2002). BS EN 1052-3 Methods of test for masonry-Part 3: Determination of initial shear strength. British standard (Vol. 3).
Calderón, S., Arnau, O., Sandoval, C. (2019). Detailed Micro-Modeling Approach and Solution Strategy for Laterally Loaded Reinforced Masonry Shear Walls. Engineering Structures, 201(February), 109786. https://doi.org/10.1016/j.engstruct.2019.109786
Calderón, S., Milani, G., Sandoval, C. (2021a). Simplified micro-modeling of partially-grouted reinforced masonry shear walls with bed-joint reinforcement: Implementation and validation. Engineering Structures, 234(January). https://doi.org/10.1016/j.engstruct.2021.111987
Calderón, S., Sandoval, C., Arnau, O. (2017a). Shear Response of Partially-Grouted Reinforced Masonry Walls with a Central Opening: Testing and Detailed Micro-Modelling. Materials and Design, 118, 122–137. https://doi.org/10.1016/j.matdes.2017.01.019
Calderón, S., Sandoval, C., Arnau, O. (2017b). Shear Response of Partially-Grouted Reinforced Masonry Walls with A Central Opening: Testing and Detailed Micro-Modelling. Materials and Design, 118, 122–137. https://doi.org/10.1016/j.matdes.2017.01.019
Calderón, S., Sandoval, C., Milani, G., Arnau, O. (2021b). Detailed micro-modeling of partially grouted reinforced masonry shear walls: extended validation and parametric study. Archives of Civil and Mechanical Engineering, 21(3), 1–24. https://doi.org/10.1007/s43452-021-00237-z
Calvi, G. M., Priestley, M. J. N., Kowalsky, M. J. (2008). Displacement-Based Seismic Design of Structures. Earthquake Spectra, 24(2), 555–557. https://doi.org/10.1193/1.2932170
CEN. (2007). European Norm for Methods of Test for Masonry – Part 3: Determination of Initial Shear Strength.
Chaimoon, K., Attard, M. M. (2009). Experimental and numerical investigation of masonry under three-point bending (in-plane). Engineering Structures, 31(1), 103–112. https://doi.org/10.1016/j.engstruct.2008.07.018
Chen, S.-W. J., Hidalgo, P. A., Mayes, R. L., Clough, R. W., Mcniven, H. D. (1978a). Cyclic Loading Tests of Masonry Single Piers Volume 2- Height to Width Ratio Of 1.
Chen, S.-W. J., Hidalgo, P. A., Mayes, R. L., Mcniven, H. D., Clough, R. W. (1978b). Cyclic Loading Tests of Masonry Single Piers, Volume 2 - Height to Width Ratio of 2.
Chopra, A. K. (2007). Dynamics of structures: Theory and applications to earthquake engineering. 3rd ed. Upper Saddle River, NJ: Pearson Prentice Hall.
Citto, C., Wo, S. I., Willam, K. J., Schuller, M. P. (2011). In-Place Evaluation of Masonry Shear Behavior Using Digital Image Analysis. ACI Materials Journal, 108(4). https://doi.org/10.14359/51683114
Correa, M. R. S. (2016). A 20-storey high masonry building in Brazil—Design problems and adopted strategies. In Proc., 16th Int. Brick and Block Masonry Conf (pp. 623–628).
CSA. (2014a). Canadian Standards Association (CSA) S304-14, Design of Masonry Structures. CSA Group. Mississauga, Ontario, Canada.
CSA. (2014b). Canadian Standards Association A165.1 CSA Standards on concrete masonry units. CSA Group, Mississauga, Ontario, Canada. Retrieved from https://www.researchgate.net/publication/269107473_What_is_governance/link/548173090cf22525dcb61443/download%0Ahttp://www.econ.upf.edu/~reynal/Civil wars_12December2010.pdf%0Ahttps://think-asia.org/handle/11540/8282%0Ahttps://www.jstor.org/stable/41857625
CSA. (2014c). Canadian Standards Association CSA-A179-14 Mortar and grout for unit masonry (Vol. 14).
CSA. (2024). Canadian Standards Association (CSA) S304-24, Design of Masonry Structures. Mississauga, Ontario, Canada: CSA Group.
D’Altri, A. M., de Miranda, S., Castellazzi, G., Sarhosis, V. (2018). A 3D Detailed Micro-Model for the In-Plane and Out-Of-Plane Numerical Analysis of Masonry Panels. Computers and Structures, 206, 18–30. https://doi.org/10.1016/j.compstruc.2018.06.007
Drysdale, R. G., Hamid, A. A. (2005). Masonry Structures Behaviour and Design. Canada Masonry Design Centre, Mississauga, Ontario.
Elmapruk, J., ElGawady, M. A., Hassanli, R. (2020). Experimental and Analytical Study on the Shear-Strength of Partially Grouted Masonry Walls. Journal of Structural Engineering, 146(8), 04020147. https://doi.org/10.1061/(asce)st.1943-541x.0002704
Elmapruk, J. H. (2010). Shear Strength of Partially Grouted. WASHINGTON STATE UNIVERSITY.
Elmeligy, O., AbdelRahman, B., Galal, K. (2024a). Experimental investigation of the compressive and shear behaviours of grouted and hollow masonry constructed with PVA fibre-reinforced mortar and grout. Construction and Building Materials, 415(January), 134954. https://doi.org/10.1016/j.conbuildmat.2024.134954
Elmeligy, O., AbdelRahman, B., Galal, K. (2024b). Numerical assessment of TMS 402/602-22 and CSA S304-14 seismic design provisions for partially grouted reinforced masonry shear walls failing in flexure. Engineering Structures, 303(December 2023), 117370. https://doi.org/10.1016/j.engstruct.2023.117370
Elmeligy, O., Aly, N., Galal, K. (2021). Sensitivity analysis of the numerical simulations of partially grouted reinforced masonry shear walls. Engineering Structures, 245(March), 112876. https://doi.org/10.1016/j.engstruct.2021.112876
Elmeligy, O. M. M. (2023). In-plane Cyclic Response of Slender Rectangular and Flanged Partially Grouted Reinforced Masonry Shear Walls Failing in Flexure. Concordia University, Montreal, Canada.
Ewing, R. D., El-Mustapha, A. M., Karlotis, J. C. (1990). Fem/I A Finite Element Computer Program for the Nonlinear Static Analysis of Reinforced Masonry Building Components. U.S. - Japan Coordinated Program for Masonry Building Research (Vol. 53). https://doi.org/10.1017/CBO9781107415324.004
Ezzeldin, M., El-Dakhakhni, W., Wiebe, L. (2018). Reinforced Masonry Building Seismic Response Models for ASCE/SEI-41. Journal of Structural Engineering, 144(1), 04017175. https://doi.org/10.1061/(asce)st.1943-541x.0001914
Ezzeldin, M., Wiebe, L., El-Dakhakhni, W. (2016). Seismic Collapse Risk Assessment of Reinforced Masonry Walls with Boundary Elements Using the FEMA P695 Methodology. Journal of Structural Engineering, 142(11). https://doi.org/10.1061/(asce)st.1943-541x.0001579
Fava, M., Munari, M., da Porto, F., Modena, C. (2016). Seismic vulnerability assessment of existing masonry buildings by nonlinear static analyses and fragility curves. Brick and Block Masonry: Trends, Innovations and Challenges - Proceedings of the 16th International Brick and Block Masonry Conference, IBMAC 2016, 2409–2416. https://doi.org/10.1201/b21889-315
Gilbert, R., Warner, R. (1978). Tension Stiffening in Reinforced Concrete Slabs. Journal of the Structural Division, 104(12), 1885–1900.
Gouda, O., Hassanein, A., Youssef, T., Galal, K. (2021). Stress-Strain Behaviour of Masonry Prisms Constructed with Glass Fibre-Reinforced Grout. Construction and Building Materials, 267, 120984. https://doi.org/10.1016/j.conbuildmat.2020.120984
Halucha, J. A. (2002). In-Plane Shear Behaviour of Reinforced Concrete Masonry Panels Under Biaxial Loading. M.A.Sc. Thesis, McMaster University. Hamilton, Ontario.
Hamedzadeh, A. (2013). On The Shear Strength Of Partially Grouted Concrete Masonry. CALGARY, ALBERTA. https://doi.org/10.11575/PRISM/27195
Hamid, A. A., Gouda, M. G. (1991). Partially Reinforced Concrete Masonry. Brick and Block Masonry, 1, 368–378.
Hansen, K. F., Nykanen, E., Gottfredsen, F. R. (1998). Shear behaviour of bed joints at different levels of precompression. Masonry International, 12(2), 70–78.
Hashemi, A., Mosalam, K. M. (2006). Shake-table experiment on reinforced concrete structure containing masonry infill wall. Earthquake Engineering & Structural Dynamics, 35(14), 1827–1852. https://doi.org/10.1002/eqe.612
Hendry, A. W. (1998). Structural Masonry. London: Macmillan Education UK. https://doi.org/10.1007/978-1-349-14827-1
Hidalgo, P. A., Mayes, R. L., Mcniven, H. D., Clough, R. (1978). Cyclic Loading Tests of Masonry Single Piers, Volume 1. Height to Width Ratio Of 2.
Hoque, N. (2013). In-Plane Cyclic Testing of Reinforced Concrete Masonry Walls to Assess the Effect of Varying Reinforcement Anchorage and Boundary Conditions. CALGARY, ALBERTA. https://doi.org/10.11575/PRISM/26545
Hsu, L. S., Hsu, C.-T. T. (1994). Complete Stress-Strain Behaviour of High-Strength Concrete Under Compression. Magazine of Concrete Research, 46(169), 301–312. https://doi.org/10.1680/macr.1994.46.169.301
Inc., T. M. (2022). MATLAB version: 9.13.0 (R2022b). Natick, Massachusetts, United States: The MathWorks Inc. Retrieved from https://www.mathworks.com
Johnson, C. A., Schultz, A. E. (2014). Simulated Seismic Testing of Partially-Grouted Masonry Subassemblages. NCEE 2014 - 10th U.S. National Conference on Earthquake Engineering: Frontiers of Earthquake Engineering. https://doi.org/10.4231/D3HX15R69
Khalaf, F. M. (2005). New Test for Determination of Masonry Tensile Bond Strength. Journal of Materials in Civil Engineering, 17(6), 725–732. https://doi.org/10.1061/(ASCE)0899-1561(2005)17:6(725)
Khan, M., Cao, M., Ali, M. (2018). Effect of basalt fibers on mechanical properties of calcium carbonate whisker-steel fiber reinforced concrete. Construction and Building Materials, 192, 742–753. https://doi.org/10.1016/j.conbuildmat.2018.10.159
Lin, C.-S., Scordelis, A. C. (1975). Nonlinear Analysis of RC Shells of General Form. Journal of the Structural Division, 101(3), 523–538.
Lizárraga, J. F., Pérez-Gavilán, J. J. (2017). Parameter estimation for nonlinear analysis of multi-perforated concrete masonry walls. Construction and Building Materials, 141, 353–365. https://doi.org/10.1016/j.conbuildmat.2017.03.008
Lourenço, P. (1996). Computational Strategy for Masonry Structures.
Lourenço, P. B., Barros, J. O., Oliveira, J. T. (2004). Shear testing of stack bonded masonry. Construction and Building Materials, 18(2), 125–132. https://doi.org/10.1016/j.conbuildmat.2003.08.018
Lourenço, P. B., Ramos, L. F. (2004). Characterization of Cyclic Behavior of Dry Masonry Joints. Journal of Structural Engineering, 130(5), 779–786. https://doi.org/10.1061/(ASCE)0733-9445(2004)130:5(779)
Lourenço, P. B., Rots, J. G. (1997). Multisurface Interface Model for Analysis of Masonry Structures. Journal of Engineering Mechanics, 123(7), 660–668. https://doi.org/10.1061/(ASCE)0733-9399(1997)123:7(660)
Magenes, G., Calvi, G. M. (1997). In-plane seismic response of brick masonry walls. Earthquake Engineering & Structural Dynamics, 26(11), 1091–1112. https://doi.org/10.1002/(SICI)1096-9845(199711)26:11<1091::AID-EQE693>3.0.CO;2-6
Mahrous, A., AbdelRahman, B., Galal, K. (2022). Seismic response analysis of reinforced masonry core walls with boundary elements. Engineering Structures, 270(September), 114882. https://doi.org/10.1016/j.engstruct.2022.114882
Maleki, M. (2008). Behaviour of Partially Grouted Reinforced Masonry Shear Walls Under Cyclic Reversed Loading. McMaster University.
Medeiros, K. A. S., Chavez, K. H., Fonseca, F. S., Parsekian, G. A., Shrive, N. G. (2021). Parametric study of multi-story, perforated, partially grouted masonry walls subjected to in-plane cyclic actions. Canadian Journal of Civil Engineering, 48(8), 1046–1055. https://doi.org/10.1139/cjce-2020-0128
Meli, R. (1973). Behaviour of masonry walls under lateral loads. In The 5th World Congress on Earthquake Engineering (pp. 853–862).
Milani, G. (2008). 3D Upper Bound Limit Analysis of Multi-Leaf Masonry Walls. International Journal of Mechanical Sciences, 50(4), 817–836. https://doi.org/10.1016/j.ijmecsci.2007.11.003
Milani, G. (2010). 3D FE Limit Analysis Model for Multi-Layer Masonry Structures Reinforced with FRP Strips. International Journal of Mechanical Sciences, 52(6), 784–803. https://doi.org/10.1016/j.ijmecsci.2010.01.004
Milani, G. (2011a). Simple Homogenization Model for the Non-Linear Analysis of In-Plane Loaded Masonry Walls. Computers and Structures, 89(17–18), 1586–1601. https://doi.org/10.1016/j.compstruc.2011.05.004
Milani, G. (2011b). Simple Lower Bound Limit Analysis Homogenization Model for In- And Out-Of-Plane Loaded Masonry Walls. Construction and Building Materials, 25(12), 4426–4443. https://doi.org/10.1016/j.conbuildmat.2011.01.012
Minaie, E. (2009). Behavior and Vulnerability of Reinforced Masonry Shear Walls. Ph.D Thesis, Drexel University.
Minaie, E., Moon, F. L., Hamid, A. A. (2014). Nonlinear Finite Element Modeling of Reinforced Masonry Shear Walls for Bidirectional Loading Response. Finite Elements in Analysis and Design, 84, 44–53. https://doi.org/10.1016/j.finel.2014.02.001
Minaie, E., Mota, M., Moon, F. L., Hamid, A. A. (2010). In-Plane Behavior of Partially Grouted Reinforced Concrete Masonry Shear Walls. Journal of Structural Engineering, 136(9), 1089–1097. https://doi.org/10.1061/(asce)st.1943-541x.0000206
NAHB Research Center. (1998). Building Concrete Masonry Homes :Design and Construction Issues. Upper Marlboro, MD, USA.
Nasiri, E., Liu, Y. (2017). Development of a detailed 3D FE model for analysis of the in-plane behaviour of masonry infilled concrete frames. Engineering Structures, 143, 603–616. https://doi.org/10.1016/j.engstruct.2017.04.049
Nayal, R., Rasheed, H. A. (2006). Tension Stiffening Model for Concrete Beams Reinforced with Steel and FRP Bars. Journal of Materials in Civil Engineering, 18(6), 831–841. https://doi.org/10.1061/(ASCE)0899-1561(2006)18:6(831)
Nolph, H. M. (2010). In-Plane Shear Performance of Partially Grouted Masonry Shear Walls. Master. Thesis, Department of Civil and Environmental Engineering, WASHINGTON STATE UNIVERSITY.
Nolph, S. M., ElGawady, M. A. (2012). Static Cyclic Response of Partially Grouted Masonry Shear Walls. Journal of Structural Engineering, 138(7), 864–879. https://doi.org/10.1061/(asce)st.1943-541x.0000529
Paulay, T. (1997). Seismic Torsional Effects on Ductile Structural Wall Systems. Journal of Earthquake Engineering, 1(4), 721–745. https://doi.org/10.1080/13632469708962385
Paulay, T., Priestly, M. J. N. (1992). Seismic Design of Reinforced Concrete and Masonry Buildings. Hoboken, NJ, USA: John Wiley & Sons, Inc. https://doi.org/10.1002/9780470172841
Priestley, M. J. N., Calvi, G. M., Kowalsky, M. J. (2007a). Displacement based seismic design of stuctures. IUSS Press, Pavia, Italy.
Priestley, M. J. N., Elder, D. M. G. (1982). Cyclic Loading Tests of Slender Concrete Masonry Shear Walls. Bulletin of the New Zealand National Society for Earthquake Engineering, 15(1), 3–21. https://doi.org/10.5459/bnzsee.15.1.3-21
Priestley, M. J. N., G.M. Calvi, M.J.Kowalsky. (2007b). Direct Displacement-Based Seismic Design of Structures. In NZSEE Conference (Vol. 24, pp. 555–557). https://doi.org/10.1193/1.2932170
Priestley, N., Calvi, G., Kowalsky, M. (2007c). Displacement-Based Seismic Design of Structures. IUSS Press, Pavia, Italy.
Redmond, L., Stavridis, A., DesRoches, R. (2014). Development of a Finite Element Model for Partially Grouted Masonry. NCEE 2014 - 10th U.S. National Conference on Earthquake Engineering: Frontiers of Earthquake Engineering, (September 2015). https://doi.org/10.4231/D3PN8XG1V
Rizaee. (2015). Assessing Bond Beam Horizontal Reinforcement Efficacy with Different End Anchorage Conditions in Concrete Block Masonry Shear Walls. Acta Universitatis Agriculturae et Silviculturae Mendelianae Brunensis. CALGARY, ALBERTA. https://doi.org/10.11575/PRISM/25017
Sandoval, C., Arnau, O. (2017). Experimental characterization and detailed micro-modeling of multi-perforated clay brick masonry structural response. Materials and Structures/Materiaux et Constructions, 50(1). https://doi.org/10.1617/s11527-016-0888-3
Sarhosis, V., Lemos, J. V. (2018). A Detailed Micro-Modelling Approach for the Structural Analysis of Masonry Assemblages. Computers and Structures, 206, 66–81. https://doi.org/10.1016/j.compstruc.2018.06.003
Scanlon, A., Murray, D. W. (1974). Time Dependent Deflections of Reinforced Concrete Slab Deflections. Journal of the Structural Division, 100(9), 1911– 1924.
Schultz, A. E. (1994). NIST Research Program on the Seismic Resistance of Partially-Grouted Masonry Shear Walls. National Institute of Standards and Technology.
Schultz, A. E., Johnson, C. A. (2019). Seismic Resistance Mechanisms in Partially Grouted Shear Walls with New Design Details. In 13th North American Masonry Conf. The Masonry Society. Salt Lake City, UT, USA.
Shedid, M. T. (2009). Strategies To Enhance Seismic Performance of Reinforced Masonry Shear Walls. (Canada): McMaster University; 2009. Ph.D. thesis.
Shedid, M. T., El-Dakhakhni, W. W., Drysdale, R. G. (2009). Behavior of fully grouted reinforced concrete masonry shear walls failing in flexure: Analysis. Engineering Structures, 31(9), 2032–2044. https://doi.org/10.1016/j.engstruct.2009.03.006
Shedid, M. T., El-Dakhakhni, W. W., Drysdale, R. G. (2010a). Alternative Strategies to Enhance the Seismic Performance of Reinforced Concrete-Block Shear Wall Systems. Journal of Structural Engineering, 136(6), 676–689. https://doi.org/10.1061/(asce)st.1943-541x.0000164
Shedid, M. T., El-Dakhakhni, W. W., Drysdale, R. G. (2010b). Characteristics of Rectangular, Flanged, and End-Confined Reinforced Concrete Masonry Shear Walls for Seismic Design. Journal of Structural Engineering, 136(12), 1471–1482. https://doi.org/10.1061/(asce)st.1943-541x.0000253
Shing, P. B., Lotfi, H. R., Barzegarmehrabi, A., Brunner, J. (1992). Finite Element Analysis of Shear Resistance of Masonry Wall Panels with and without Confining Frames. Earthquake Engineering, Tenth World Conference.
Siyam, M. A., El-Dakhakhni, W. W., Shedid, M. T., Drysdale, R. G. (2016). Seismic Response Evaluation of Ductile Reinforced Concrete Block Structural Walls. I: Experimental Results and Force-Based Design Parameters. Journal of Performance of Constructed Facilities, 30(4), 1–14. https://doi.org/10.1061/(ASCE)CF.1943-5509.0000794
Stavridis, A., Shing, P. B. (2010). Finite-element modeling of nonlinear behavior of masonry-infilled RC frames. Journal of Structural Engineering, 136(3), 285–296. https://doi.org/10.1061/(ASCE)ST.1943-541X.116
Tagel-Din, H., Meguro, K. (2000). APPLIED ELEMENT METHOD FOR DYNAMIC LARGE DEFORMATION ANALYSIS OF STRUCTURES. Doboku Gakkai Ronbunshu, 2000(661), 1–10. https://doi.org/10.2208/jscej.2000.661_1
Taylor-Firth, A., Taylor, I. F. (1990). A bond tensile strength test for use in assessing the compatibility of Brick/Mortar interfaces. Construction and Building Materials, 4(2), 58–63. https://doi.org/10.1016/0950-0618(90)90001-H
Thurston, S. J., Hutchison, D. L. (1982). Reinforced Masonry Shear Walls: Cyclic Load Tests in Contraflexure. Bulletin of the New Zealand National Society for Earthquake Engineering, 15(1), 27–45.
Tomazevic, M. (1999). Earthquake-Resistant Design of Masonry Buildings (Vol. 1). PUBLISHED BY IMPERIAL COLLEGE PRESS AND DISTRIBUTED BY WORLD SCIENTIFIC PUBLISHING CO. https://doi.org/10.1142/p055
Tomaževič, M. (1999). Earthquake-resistant design of masonry buildings. TA - TT -. London, Singapore SE - xii, 268 pages : illustrations ; 23 cm.: Imperial College Press ; Distributed by World Scientific London, Singapore. https://doi.org/LK - https://worldcat.org/title/40776879
Usman, M., Farooq, S. H., Umair, M., Hanif, A. (2020). Axial compressive behavior of confined steel fiber reinforced high strength concrete. Construction and Building Materials, 230, 117043. https://doi.org/10.1016/j.conbuildmat.2019.117043
Valdebenito, G., Alvarado, D., Sandoval, C., Aguilar, V. (2015). Terremoto De Iquique Mw=8,2 - 01 Abril 2014: Daños Observados Y Efectos De Sitio En Estructuras De Albañilería. In XI Congr. Chil. Sismol. e Ing. Sísmica 922 ACHISINA. 18-20 March, Santiago. Chile.
Van Der Pluijm, R. (1997). Non-linear behaviour of masonry under tension. Heron, 42(1), 25–48.
Van der Pluijm, R., Rutten, H. S., Ceelen, M. (2000). Shear behaviour of bed joints. In conference; 12th International Brick/Block Masonry Conference; 2000-06-25; 2000-06-28 (p. 12).
Van derPluijm, R. (1999). Out-of-Plane Bending of Masonry Behaviour and Strength. (Phd Thesis) Technische Universiteit Eindhoven. https://doi.org/10.6100/IR528212
Vebo, A., Ghali, A. (1977). Moment-Curvature Relation of Reinforced Concrete Slabs. Journal of the Structural Division, 103(3), 515–531.
Voon, K. C., Ingham, J. M. (2003). SHEAR STRENGTH OF CONCRETE MASONRY WALLS.
Zhang, Z., Murcia-Delso, J., Sandoval, C., Araya-Letelier, G., Wang, F. (2021). In-plane shear strength and damage fragility functions for partially-grouted reinforced masonry walls with bond-beam reinforcement. Engineering Structures, 242. https://doi.org/10.1016/j.engstruct.2021.112569
All items in Spectrum are protected by copyright, with all rights reserved. The use of items is governed by Spectrum's terms of access.
Repository Staff Only: item control page
Download Statistics
Download Statistics